813412

Gazco Studio Freestanding Balanced Flue Manual

18
Zoom out
Zoom in
Previous page
1/52
Next page
18
2.26 The Inlet Extension Pipe needs to be fitted in the correct
orientation, see Diagram 11.
11
90º End
Into Appliance
Short Section
Out of Appliance
2.27 From the rear of the appliance, feed the 90º angle of the
Inlet Extension Pipe through the hole in the back of the
Plinth or Bench, see Diagram 12.
12
Hole in rear of
Plinth or Bench
Inlet Pipe
Extension
2.28 Continue to feed the pipe through the hole, rotating so that
the 90º angle is upright and guide through the silicone
panel in the base of the firebox.
2.29 Remove the isolation elbow from the appliance and
connect to the Inlet Extension Pipe inside the firebox.
2.30 Connect the isolation elbow to the appliance gas inlet pipe.
13
Inlet Pipe
Compression Elbow
Inlet Pipe
Extension
2.31 At the rear of the appliance, fit the supplied 8mm elbow to
the Inlet Extension Pipe.
WARNING: THIS APPLIANCE IS HEAVY.
USE CAUTION WHEN INSTALLING, REMOVING
AND STORING AS THE APPLIANCE IS HEAVY AND
SHOULD BE HANDLED CAREFULLY.
AT LEAST TWO PEOPLE WILL BE REQUIRED TO
INSTALL THIS APPLIANCE.
2.15 Remove the securing spring clip from the bottom-right of the
window frame, see Diagram 9.
9
2.16 With the window frame in an upright position slide the frame
to the left so that it comes off the left hinge pin, see Diagram
10 (1).
2.17 Still keeping the frame upright drop the left side down and
forward slightly, see Diagram 10 (2).
10
1
2
2.18 Slide the frame to the right so it comes off the right hinge
pin. The window frame should now be free.
2.19 Refit the Window Frame Assembly in reverse order.
When closing the door ensure the door catches are fully
engaged.
UNDER NO CIRCUMSTANCES SHOULD THE
APPLIANCE BE USED WITHOUT THE CATCHES
HOLDING THE DOOR IN PLACE.
2.20 Remove the box from the appliance and store safely as it
contains the remote control and fuel effects, etc.
2.21 Remove all the enamel liners where necessary. The rear
panels on Studio 1 can remain in place, see Replacing
Parts, Section 5.
2.22 Remove the Main Burner, see Replacing Parts, Section 6.
2.23 Remove the Main Control Assembly, see Replacing Parts,
Section 7.
2.24 The gas supply enters the appliance through a silicone
panel in the base of the firebox.
2.25 Slit the silicone panel with a sharp knife.
Installation Instructions
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Studio Freestanding Balanced Flue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Studio Freestanding Balanced Flue in the language / languages: English as an attachment in your email.

The manual is 8.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info