813405
34
Zoom out
Zoom in
Previous page
1/40
Next page
34
SERVICING INSTRUCTIONS
REPLACING PARTS - BALANCED FLUE
3.10 Remove the external inlet pipe from the brass fitting (see
Diagram 8 arrow B).
3.11 Remove the control box by undoing the 2 x screws securing
it to the base of the appliance (see Diagram 9).
9
AR2587
Control Box Screws
Screw
3.12 Remove the screw next to the battery box (see Diagram 9).
Gently slide the gas valve and bracket forward and
disconnect the thermocouple from the rear of the gas valve.
3.13 Push the thermocouple down through the hole in the base
of the firebox and remove the component.
3.14 When fitting the new component after it has been shaped
to the old thermocouple, push the tip (pilot end) through
the hole from under the firebox floor. Do not insert the tip
into the pilot burner at this stage.
3.15 Connect the thermocouple at the gas valve, do not over
tighten the nut.
3.16 Assemble the gas valve bracket on to the firebox base and
all pipes to the valve and fittings.
3.17 Insert the tip of the thermocouple into the pilot burner and
tighten the nut. Replace the silicone around the
thermocouple and ignition lead. Screw the plate into
position, replace the pilot cover, log support and replace
the ceramics.
3.18 Check the pilot flame length (see Diagram 10).
13
7
AR0620
10
4. IGNITION LEAD
4.1 Unplug the ignition lead from the control box (see Diagrams
11).
11
AR2587
Ignition Lead
Control Box
4.2 Remove the burner as described in Section 2, pilot cover
and plate as described in Section 3.
4.3 Disconnect the ignition lead from the electrode and
push the lead complete with the vidaflex through the base
of the appliance.
4.4 Cut the cable tie and remove the vidaflex sleeve. THIS
MUST BE KEPT AND ASSEMBLED ON THE NEW LEAD. A
CABLE TIE MUST ALSO BE USED TO RETAIN THE SLEEVE.
4.5 The lead can only be fitted one way round, ensure this is
correct when refitting a replacement.
4.6 When replacing the cover plate ensure silicone sealant is
used to seal the aperture.
5. GAS VALVE
5.1 Turn the gas supply off at the isolation elbow, and
disconnect from the inlet pipe on the appliance.
5.2 Disconnect the inlet pipe at the pressure test point (see
Diagram 12).
12
AR2587
Pressure test point
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva F67 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva F67 in the language / languages: English as an attachment in your email.

The manual is 4.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info