813407
19
Zoom out
Zoom in
Previous page
1/40
Next page
19
Installation Instructions
4.11 Position the flue collar onto the top of the appliance,
see Diagram 10.
10
4.12 Connect the flue system.
5. Apex Stand Installation
5.1 Ensure that all minimum clearances to combustible
materials have been complied with, see Site
Requirements.
There are key slots on the base of the Apex Stand for fixing
to the floor.
To secure the Apex Standing to the floor:
5.2 Decide on the position of the stand and appliance.
Ensuring that a minimum 50mm clearance is left from the
back of the stand to the rear wall, see Diagram 11.
5.3 Mark the centre line.
5.4 Add 148mm to the desired distance from the back wall, to
give the total distance in Diagram 11 (198mm minimum).
Draw a line parallel to the wall.
11 Wall
Back of Apex Stand
Fixing Screws Fixing Screws
50 (min)
148
Total
Distance
198 min
300 300
5.5 Along the parallel line, measure and mark on the floor
300mm from both sides of the centre line, see Diagram 11.
This will give the position of the fixing holes.
5.6 Drill the holes and insert the rawl plugs.
5.7 Fit the screws, leaving a minimum of 5mm between the floor
and the underside of the screw heads.
4. Bench Installation
4.1 Ensure that all minimum clearances to combustible
materials have been complied with, see Site
Requirements.
To secure the bench to the floor:
4.2 Position the bench where required and mark its position on
the floor through the keyholes in the small opening on both
legs, see Diagram 8.
8
4.3 Remove the bench and drill and fit fixing screws in the floor.
4.4 Partially tighten providing enough margin to then manoeuvre
the bench and slide the keyholes into the screws.
4.5 Tighten the screws fully.
4.6 To secure the appliance to the bench the position of the
appliance must considered before using the template, see
Diagram 9.
9
4.7 Using the template as a guide to the final position of the
appliance, mark and drill the holes.
4.8 Position the appliance on the bench lining up the holes in its
base with the holes you have drilled in the bench.
4.9 Fit the fixing screws.
4.10 Connect the gas supply to the gas Inlet pipe at the back of
the appliance.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva 2 F670 Conventional Flue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva 2 F670 Conventional Flue in the language / languages: English as an attachment in your email.

The manual is 4.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info