813469
14
Zoom out
Zoom in
Previous page
1/28
Next page
14
6. Replacing the Motor & Effects Unit
Motor
unit
Plug
6
6.1 The motor & effects unit is attached by 4 x screws located at
the rear of the appliance. It may be necessary to move the
appliance from its location to gain access to the rear of the
stove. Remove the 4 screws on the lower rear casing.
Note: There are 2 x gaskets between the unit and the
appliance. Remove and keep in a safe place.
6.2 Disconnect the 2 x wires connecting the 2 x 'flying' LEDs
to the front LED board, noting their orientation.
6.3 Lift and rotate the motor unit to give access to the rear
LED board.
6.4 Disconnect both wires from the rear LED board, noting the
orientation.
6.5 Unplug the cables connecting the motor unit and the PCB.
6.6 The motor and effects unit can now be removed and
replaced as a whole unit.
6.7 Replace in reverse order. Ensure to replace gaskets when
reattaching motor to appliance body and that all wires are
correctly connected.
7. Replacing the Middle LED Board
7.1 The middle LED board is attached to the motor unit but can
be replaced individually, see Diagram 7.
Rear LED board
Middle
LED
board
7
7.2 Disconnect the wire connecting the middle LED board to the
rear LED board, noting its orientation.
7.3 Attach the new board and reconnect the wire.
8. Replacing the Rear LED Board
The rear LED board is attached to the motor unit but can be
replaced individually, see Diagram 7.
8.1 Remove the motor unit following instructions in section 6 (it
is not necessary to disconnect the motor unit from the
PCB) and rotate to access the rear LED board.
8.2 Release the board by removing the 2 x screws at either
end of it.
8.3 Disconnect the wire connecting the rear LED board to the
front LED board, noting its orientation.
8.4 Attach the new board using the 2 x screws and reconnect
the wire.
8.5 Replace motor and effects unit (see Section 6). Ensure to
replace gaskets when reattaching motor to appliance
body and that all wires are correctly connected.
9. Replacing the Heater Assembly
9.1 To access the heater assembly remove any loose top plates
or panels before moving the stove and carefully lay the stove
on its back.
9.2 Remove the 5 x screws securing the heater casing to the
bottom of the firebox, see Diagram 8.
Screws
Heater Assembly Case
Bottom of Firebox
8
Servicing Instructions
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Marlborough - Electric at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Marlborough - Electric in the language / languages: English as an attachment in your email.

The manual is 4.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gazco Marlborough - Electric

Gazco Marlborough - Electric User Manual - Dutch - 20 pages

Gazco Marlborough - Electric User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info