813469
13
Zoom out
Zoom in
Previous page
1/28
Next page
13
Servicing Instructions
3. Servicing Requirements
THIS APPLIANCE MUST ONLY BE SERVICED BY A
SUITABLY QUALIFIED PERSON.
BEFORE UNDERTAKING ANY WORK ON THE
APPLIANCE:
3.1 Switch off the appliance and isolate it from the mains by
unplugging the unit.
3.2 Wait for at least 10 minutes until the appliance has
cooled down.
3.3 Following the appropriate instructions from User
Instructions, Section 4, remove the door and glass front.
3.4 Remove the screws on the lower panel on the front of the
appliance and carefully remove the fuel bed, see
Diagram 3.
Please note: The fuel bed is secured by 2 x screws on
the lower panel on the front of the stove.
Screws Fuel bed
3
4. Replacing the front LED Board
4.1 If an LED fails to light you will notice an uneven or unlit fuel
effect. For middle and rear boards see Sections 7 & 8.
4.2 To replace the front LED board disconnect all wires, noting
their orientation.
4.3 The board is secured by 2 x plastic push fasteners, see
Diagram 4. Using pliers, gently squeeze the head of the
fasteners to release the board.
Front LED board
Plugs
Push fasteners
4
4.4 Dispose of the board at an appropriate recycling centre.
4.5 To connect the new LED board push the fasteners through
the ready drilled holes and ensure that all wires are correctly
connected.
5. Replacing the Printed Circuit Board
5.1 To remove the PCB first remove the front LED board
following instructions Section 4.
5.2 The PCB is fixed to the base of the appliance using 2 x
push fasteners and 2 x screws, see Diagram 5.
Release board from fasteners and remove screws.
PCB
5
5.3 The wires should now be disconnected from the PCB one
by one. As each wire is disconnected from the old PCB
attach it to the new PCB to ensure correct orientation.
5.4 Fix the new PCB to the base of the appliance using the
2 x push fasteners and 2 x screws.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Marlborough - Electric at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Marlborough - Electric in the language / languages: English as an attachment in your email.

The manual is 4.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gazco Marlborough - Electric

Gazco Marlborough - Electric User Manual - Dutch - 20 pages

Gazco Marlborough - Electric User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info