813483
24
Zoom out
Zoom in
Previous page
1/52
Next page
24
Installation Instructions
3.36 TAKE CARE TO MARK OUT THE FLUE CORRECTLY. IT
IS DIFFICULT TO MOVE AFTER INSTALLATION.
3.37 Create a 152mm (6”) diameter hole for the flue using either:
a) a core drill, or
b) a hammer and chisel
3.38 Make good at both ends of the hole.
Flue Length
3.39 The final length of the flue pipe includes the terminal. The
terminal is the only section that can be shortened.
DO NOT SHORTEN ANY OTHER SECTION OF FLUE
PIPE.
3.40 Measure from the outside of the wall to the stop on the 90°
elbow.
3.41 Fit horizontal flue section between the elbow and the
terminal at this stage, if required, see Diagram 7.
10mm
Wall plate
7
3.42 Mark the correct length all the way around the flue terminal
section, see Diagram 8.
3.43 Insert the square cardboard sleeve into the flue to support
the inner tube.
3.44 Cut through the flue and sleeve, see Diagram 8.
8
3.45 REMOVE THE CARDBOARD REMNANTS FROM THE
FLUE.
3.46 File the cut edge smooth.
Flue and Appliance Fixings
3.47 Pull appliance and flue assembly away from the hearth.
3.48 Drill four fixing holes for the wall plate and insert
wall plugs supplied.
3.49 Put the horizontal flue onto the elbow and reposition the
appliance.
3.50 Check the flue runs smoothly through the wall.
3.51 Fix the wall plate to the wall using the four black screws
provided.
3.52 Drill through the fixing tab of the wall plate using a
3.5mm drill.
3.53 Secure with the screw provided.
3.54 Make good and weatherproof around the outside of the flue.
3C. Top Exit – Vertical Flue
(Huntingdon 30 & 40 only)
3.55 Where a vertical only flue system has been purchased, refer
to Installation & Instructions, Site Requirements, Section 4D.
3.56 Pay careful attention to the following:
Terminal positions
Flue supports
Weatherproofing
Fire precautions
3.57 Local and national codes of practice must be followed for all
the above.
TOP EXIT – VERTICAL ONLY, INCLUDING OFFSET
3.58 A restrictor must be fitted with vertical flues. See
technical specification on page 14 for restrictor size.
3.59 It is important that the sliding restrictor assembly is used.
The restrictor assembly must be fitted with the slide collars
uppermost and the top restrictor plate must be checked to
ensure it moves freely before the flue is fitted.
Restrictor assembly
Slide collars
9
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Huntingdon 20-30-40 - Balanced Flue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Huntingdon 20-30-40 - Balanced Flue in the language / languages: English as an attachment in your email.

The manual is 3.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info