691438
5
Zoom out
Zoom in
Previous page
1/6
Next page
4
Mark new pilot-hole locations if necessary, and remove the
device from the mounting surface.
5
Drill the remaining pilot holes.
6
Secure the device to the mounting location.
Blink Codes
After the sonar module is installed, it turns on when the
chartplotter is turned on. The color status LED on the sonar
module indicates its operational status.
LED Color State Status
Green Blinking The sonar module is connected to a
chartplotter and is operating properly.
You should see sonar data on the
chartplotter.
Red Blinking The sonar module is turned on, but is
not connected to a chartplotter, or is
waiting to connect to a chartplotter. If the
sonar module is connected to the
chartplotter and this code persists,
check the wiring connections.
Orange Blinking A software update is in progress.
Red/Green Blinking Reserved
Red Two blinks
followed by a 3-
second pause
Other sonar failure.
Red Three blinks
followed by a 3-
second pause
The transducer is not detected by the
sonar module. If this code persists,
check the wiring connections.
Red Five blinks
followed by a 3-
second pause
The sonar module input voltage exceeds
the maximum input voltage.
Installation Diagram
Compatible Garmin chartplotter
Panoptix LiveScope GLS 10 sonar module
Garmin Marine Network small connector to full-size GarminMarine
Network adapter cable
RJ-45 connector
Garmin Marine Network cable small connector
7.5 A fast-acting fuse (required, not included)
NOTICE
You must connect the power wire through a 7.5 A fast-acting fuse
(not included). If you omit a fuse, the device can malfunction.
Power cable
Transducer cable
Panoptix LiveScope LVS32 transducer
Power Cable Extensions
If necessary, you can extend the power cable using the
appropriate wire gauge for the length of the extension.
Item Description
Fuse
Battery
9 ft. (2.7 m) no extension
Item Description
Splice
10 AWG (5.26 mm²) extension wire, up to 4.6 m (15 ft.)
8 AWG (8.36 mm²) extension wire, up to 7 m (23 ft.)
6 AWG (13.29 mm²) extension wire, up to 11 m (36 ft.)
Fuse
8 in. (20.3 cm)
Battery
8 in. (20.3 cm)
Maximum extension 36 ft. (11 m)
Calibrating the Compass
Before you can calibrate the compass, the transducer must be
installed on the shaft far enough away from the trolling motor to
avoid magnetic interference, and deployed in the water.
Calibration must be of sufficient quality to enable the internal
compass.
NOTE: To use the compass, you must mount the transducer on
the transom or the trolling motor shaft. The compass may not
work when you mount the transducer on the motor.
NOTE: For best results, you should use a heading sensor such
as the SteadyCast
heading sensor.
You can begin turning your boat before calibrating, but you must
fully rotate your boat 1.5 times during calibration.
1
From an applicable sonar view, select MENU > Sonar Setup
> Installation.
2
If necessary, select Use AHRS to turn on the AHRS sensor.
3
Select Calibrate Compass.
4
Follow the on-screen instructions.
Maintenance
Cleaning the Transducer
Aquatic fouling accumulates quickly and can reduce your
device's performance.
1
Remove the fouling with a soft cloth and mild detergent.
2
Wipe the device dry.
Specifications
Panoptix LiveScope LVS32 Specifications
Dimensions (L x H x W) 136.4 x 96.5 x 44.5 mm (5.37 x 3.8
x 1.75 in.)
Weight (transducer only) 850 g (1.87 lbs.)
Frequencies From 530 to 1.1 MHz
Operating temperature From 0 to 40°C (from 32 to 104°F)
5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Panoptix Livescope at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Panoptix Livescope in the language / languages: English as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Panoptix Livescope

Garmin Panoptix Livescope Installation Guide - German - 6 pages

Garmin Panoptix Livescope Installation Guide - Dutch - 6 pages

Garmin Panoptix Livescope Installation Guide - French - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info