691438
3
Zoom out
Zoom in
Previous page
1/6
Next page
3
Secure the transducer cable to the motor shaft or other
secure location.
4
Route the transducer cable to the installation location of the
sonar module while taking these precautions.
You should not route the cable close to electrical wires or
other sources of electrical interference.
You must route the cable so it is not pinched when the
trolling motor is deployed or stowed.
NOTE: If necessary, for extra cable length you can connect
an optional extension cable, available at buy.garmin.com or
from your Garmin dealer.
5
Position the transducer to your desired angle (Trolling Motor
Mount Orientation, page 3).
Trolling Motor Mount Orientation
The orientation depends on which side of the trolling motor you
have mounted the transducer on, and your desired field of view.
TIP: No tools are necessary to change the orientation from
forward to down. Turn the mount one click to change the
orientation from forward to down.
Starboard side, forward view
Starboard side, downward view
Port side, forward view
Port side, downward view
Installing the Transducer on a Trolling Motor
Shaft
Trolling Motor Shaft Bracket Orientation
The trolling motor shaft bracket features an 8-degree cant to
reduce the effects of the trolling motor barrel interference with
the transducer beam. You must orient the arrow and the
narrow end of the angle to the top when you attach the
bracket to the trolling motor shaft.
Assembling the Trolling Motor Shaft Mount Hardware
With the trolling motor bracket oriented correctly (Trolling
Motor Shaft Bracket Orientation, page 3), use the included
hex wrench to attach the transducer to the trolling shaft
bracket with the shoulder screw , flat washer , and
rubber washer .
NOTE: You must fully tighten the mount to the transducer.
The recommended torque applied to the shoulder screw is
2.5 lb-ft. (3.4 N-m).
Installing the Transducer on the Trolling Motor Shaft
NOTICE
You must secure the transducer cable to the shaft or other
secure location during installation. Damage to the transducer
cable wire or the cable jacket can cause transducer failure.
You should mount the transducer as far from the motor as
possible.
You should use the included rubber insert on a 25 mm (1 in.)
trolling motor shaft.
1
Using the included hex wrench, insert the M6 screws and
attach the shaft trolling bracket to the transducer bracket
around the trolling motor shaft.
2
Secure the transducer cable to the motor shaft or other
secure location.
3
Route the transducer cable to the installation location of the
sonar module while taking these precautions.
You should not route the cable close to electrical wires or
other sources of electrical interference.
You must route the cable so it is not pinched when the
trolling motor is deployed or stowed.
4
Position the transducer to your desired angle (Trolling Motor
Shaft Orientation, page 3).
Trolling Motor Shaft Orientation
The angle of installation depends on the side of the trolling
motor shaft you mount the bracket on, and your desired field of
view.
TIP: No tools are necessary to change the orientation from
forward to down. Turn the mount one click to change the
orientation from forward to down.
3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Panoptix Livescope at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Panoptix Livescope in the language / languages: English as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Panoptix Livescope

Garmin Panoptix Livescope Installation Guide - German - 6 pages

Garmin Panoptix Livescope Installation Guide - Dutch - 6 pages

Garmin Panoptix Livescope Installation Guide - French - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info