691438
2
Zoom out
Zoom in
Previous page
1/6
Next page
Installing the Transducer on a Trolling Motor
Assembling the Trolling Motor Barrel Mount Hardware
1
Align the top of the transducer with the top of the bracket
.
2
Using the included hex wrench, attach the bracket to the
transducer with the shoulder screw , rubber washer , and
flat washer .
NOTE: You must fully tighten the mount to the transducer.
The recommended torque applied to the shoulder screw is
2.5 lb-ft. (3.4 N-m).
Separating the Transducer Cables
Before you separate the cables, you should test-fit the
transducer. The cables should be at room temperature when
you separate them.
1
With the transducer dry fitted to the trolling motor, mark the
location the transducer cable crosses the rotating joint .
2
Place the transducer cables on a hard, flat surface.
3
Press the tip of the cutting tool, a flathead screwdriver, or a
blunt knife to the center of the cables at your marked
location, and puncture the material between the cables.
NOTE: Do not cut through or into the round section of the
cables. Puncture the center webbing between the cables
only.
4
Using your fingers, pull the cable halves apart approximately
12.5 cm (5 in.) on both sides of the hole.
5
Ensure the cables have a gap of at least 10 cm ( 4 in.) above
and 10 cm (4 in.) below the split portion of the cable and
are centered on the rotating joint . This creates a loop in
the cable over the rotating joint. The loop must be large
enough to allow full rotation of the transducer in both
directions. Allow a minimum of 25 cm (10 in.) of cable to
cover the 20 cm (8 in.) section between mounting points.
6
Use the black electrical tape to secure the transducer
cable to the shaft. The split section of the cable should
extend under the tape.
7
Test the full rotation of the trolling motor to ensure the cables
clear the rotating joint and are not pulled due to tension
during rotation.
Installing the Transducer on a Trolling Motor
NOTICE
You must secure the transducer cable to the shaft or other
secure location during installation. Damage to the transducer
cable wires or cable jacket can cause transducer failure.
1
Insert the hose clamp through the slot on the trolling motor
mount until equal lengths extend on both sides of the
mount.
2
Secure the hose clamp around the trolling motor .
NOTE: Do not rotate the transducer.
2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Panoptix Livescope at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Panoptix Livescope in the language / languages: English as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Panoptix Livescope

Garmin Panoptix Livescope Installation Guide - German - 6 pages

Garmin Panoptix Livescope Installation Guide - Dutch - 6 pages

Garmin Panoptix Livescope Installation Guide - French - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info