584001
91
Zoom out
Zoom in
Previous page
1/124
Next page
400 SERIES INSTALLATION MANUAL Page 5-9
P/N 190-00140-02 Page Rev L
TO-FROM
Selection Verify That:
FROM
The FROM flag is in view.
Hidden
The TO/FROM flag is hidden.
TO
The TO flag is in view.
SELECTED COURSE
Select 150° on the CDI/HSI that is connected to the 400 Series unit’s MAIN OBS inputs. The
SELECTED COURSE field indicates near to 150° and a Calibrate to 150°? field appears. Selecting this
field calibrates the 400 Series unit to match the input source. Verify OBS operation by checking that the
course displayed on the 400 Series unit is within 2° of the selected course. Do this at 30° intervals around
the OBS card.
NOTE
If it is desired to ignore a selected course input (either analog resolver or ARINC 429) for GPS operation in
OBS mode, press MENU on the MAIN CDI/OBS CONFIG page and select “Ignore SEL CRS for GPS?”.
When OBS mode is selected, the selected course is entered on the controls of the 400 Series unit. If
ignoring the selected course input such that the VOR valid flag is dependent only on a valid VOR signal,
with lateral deviation calculated by another display device, press MENU on the MAIN CDI/OBS CONFIG
page and select “Ignore SEL CRS for VLOC?”.
CDI (GNS 430 Only)
Selection Description
GPS
The GNS 430 CDI button is in the GPS state, and the GPS ANNUNCIATE
output is active. This annunciator output may be required to be active for
some installations.
VLOC
The GNS 430 CDI button is in the VLOC state, and the VLOC
ANNUNCIATE output is active.
NOTE
If it is desired to disable the GNS 430 CDI key, press MENU on the MAIN CDI/OBS CONFIG page and
select “Ignore CDI Key?”. This causes the field above the CDI key to always display GPS, regardless of
CDI key presses. This may be necessary for certain EFIS systems where navigation sensor selection must
be accomplished on the EFIS or its control panel.
OBI SOURCE (GNS 430 Only)
Selection Description
Always GPS
The MAIN King Serial OBI outputs are always GPS. This is useful if it is
desired to switch a Bendix/King KI 229 or KNI 582 RMI pointer
independently from the GNS 430 CDI button.
Track CDI
The MAIN King Serial OBI outputs are GPS or VOR, and switchable by the
GNS 430 CDI button. This is useful if it is desired the Bendix/King KI 229
or KNI 582 RMI pointer to display the same navigation source as the GNS
430 CDI outputs.
V-FLAG STATE
Selection Description
Declutter
The vertical deviation bar is parked in the full-scale up position when GPS or
VOR navigation is selected for output. The exception is when the CDI is in
VLOC mode and an ILS frequency is tuned, in which case the vertical
deviation bar parks in the centered position.
Normal
The vertical deviation bar parks in the centered position whenever it is
flagged.
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNS 430 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNS 430 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info