584001
89
Zoom out
Zoom in
Previous page
1/124
Next page
400 SERIES INSTALLATION MANUAL Page 5-7
P/N 190-00140-02 Page Rev L
OFFSET
Adjusts the lighting level up or down for any given input level. This field has a range of 0 (zero) to 99,
and is set to 50 at the factory. This may also be used to match lighting curves with other equipment in the
panel.
PHOTO TRANS % - (Photocell Transition Percentage)
When a lighting bus is used to control the lighting of the
display (see Figure 5-7), this parameter sets the point on
the lighting bus control below which the display brightness
tracks the 400 Series unit’s photocell. This field has a
range of 0 (zero) to 99, and is set to 25 at the factory.
PHOTO SLP/OFFST - (Photocell Slope/Offset)
These fields are equivalent to the SLOPE/OFFSET fields
described above, with the exception that they only control
the display lighting characteristics when the lighting bus control is below the level specified in the PHOTO
TRANS % field. Both fields have a range of 0 (zero) to 99, and are set to 50 at the factory.
CONTRAST
If contrast isn’t acceptable, place unit in Normal Mode. On
the AUX menu SETUP page 2, highlight DISPLAY and
press ENTER. The DISPLAY page is shown (see Figure
5-8). Confirm that CONTRAST MODE is “Auto”.
Highlight CONTRAST LEVEL and adjust to best
viewable color. Press ENTER to confirm change.
NOTE
Note: Leave CONTRAST MODE in “Auto”.
5.2.7 DATE/TIME SETUP Page
Select the DATE/TIME SETUP Page (see Figure 5-9).
Very infrequently, it may be desirable to set the date and
time of the 400 Series unit to aid in acquiring a GPS
position. Configuration mode is the only means by which
the date and time for the 400 Series unit may be adjusted.
Note that the time must be UTC time, and that the UTC
date may be different from the date in the local time zone.
5.2.8 MAIN DISCRETE INPUTS Page
Select the MAIN DISCRETE INPUTS Page (see Figure 5-
10) if the encoding altimeter input is used. Verify that the
DECODED ALTITUDE field indicates the correct
altitude.
EXTERNAL SWITCH STATE
Selection Verify That:
RMT CDI
The box is filled in while a remote CDI source select switch is pressed.
RMT OBS
The box is filled in while a remote OBS switch is pressed.
Figure 5-7. MAIN LIGHTING Page
(Display Lighting from Lighting Bus)
Figure 5-8.
DISPLAY Page (AUX Group)
Figure 5-9.
DATE/TIME SETUP Page
Figure 5-10.
MAIN DISCRETE INPUTS Page
89


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNS 430 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNS 430 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info