Manual Garmin Edge 510 (page 10 of 20) (English)

501751

Zoom out

Zoom in

1/20

Loosely attach the GSC 10 using two cable ties

Attach the pedal magnet

to the crank arm using the

adhesive mount and a cable tie

The pedal magnet must be within 5 mm of the GSC 10. The

indication line

on the pedal magnet must line up with the

indication line

on the GSC 10.

Unscrew the spoke magnet

from the plastic piece.

Place the spoke in the groove of the plastic piece, and

tighten it slightly.

The spoke magnet can face away from the GSC 10 if there is

not enough room between the sensor arm and the spoke.

The spoke magnet must line up with the indication line

the sensor arm.

Loosen the screw

on the sensor arm.

Move the sensor arm to within 5 mm of the spoke magnet.

You can also tilt the GSC 10 closer to either magnet to

improve alignment.

Select Reset

on the GSC 10.

The LED turns red, then green.

Pedal to test the sensor alignment.

The red LED blinks each time the pedal magnet passes the

sensor. The green LED blinks each time the spoke magnet

passes the sensor arm.

NOTE: The LED blinks for the first 60 passes after a reset.

Select Reset again if you require additional passes.

When everything is aligned and working correctly, tighten the

cable ties, the sensor arm, and the spoke magnet.

Garmin recommends that the torque is 1.9 to 2.4 lbf-in. (0.21

to 0.27 N-m) to ensure a water tight seal on the GSC 10

sensor arm.

About the GSC 10

Cadence data from the GSC 10 is always recorded. If there is

no GSC 10 paired, GPS data is used to calculate the speed and

distance.

Cadence is your rate of pedaling or “spinning” measured by the

number of revolutions of the crank arm per minute (rpm). There

are two sensors on the GSC 10: one for cadence and one for

speed.

Data Averaging for Cadence or Power

The non-zero data-averaging setting is available if you are

training with an optional cadence sensor or power meter. The

default setting is to exclude zero values that occur when you are

not pedaling.

To change this setting, see page 8.

Training with Power Meters

• Go to www.garmin.com/intosports for a list of third-party

ANT+ sensors that are compatible with your device.

• For more information, see the owner's manual for your power

meter.

• Adjust your power zones to match your goals and abilities

(page 6).

• Use range alerts to be notified when you reach a specified

power zone (page 3).

• Customize the power data fields (page 9).

Setting Your Power Zones

The values for the zones are default values and may not match

your personal abilities. You can manually adjust your zones on

the device or using Garmin Connect. If you know your functional

threshold power (FTP) value, you can enter it and allow the

software to calculate your power zones automatically.

From the home screen, select > Training Zones >

Power.

Enter your FTP value.

Select Based On:.

Select an option:

• Select Watts to view and edit the zones in watts.

• Select % FTP to view and edit the zones as a percentage

of your functional threshold power.

Calibrating Your Power Meter

Before you can calibrate your power meter, it must be properly

installed, paired with your GPS device, and actively recording

data.

For calibration instructions specific to your power meter, refer to

the manufacturer's instructions.

From the home screen, select .

Select Bike Profiles.

Select a profile.

Select > Calibrate.

Keep your power meter active by pedaling until the message

appears.

Follow the on-screen instructions.

Pairing Your ANT+ Sensors

Before you can pair, you must put on the heart rate monitor or

install the sensor.

6 ANT+ Sensors

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Edge 510 in the language / languages: English as an attachment in your email.

The manual is 3,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Edge 510

Garmin Edge 510 User Manual - German - 22 pages

Garmin Edge 510 User Manual - Dutch - 22 pages

Garmin Edge 510 User Manual - French - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Garmin Edge 510 Manual

Product: