691049
7
Zoom out
Zoom in
Previous page
1/14
Next page
Installing AA Batteries
The device operates on two 1.5 V AA batteries (not included).
For the best results, you should use lithium batteries, which
provide extended battery life and better performance at low
temperatures.
NOTICE
Do not use AA batteries with a voltage specification higher than
1.5 V. Higher voltages will cause permanent damage to the
camera. Do not use lithium-ion rechargeable AA battery cells.
Lithium-ion batteries use a different technology that non-
rechargeable lithium batteries and may permanently damage the
camera.
1
Rotate both battery covers toward the front of the camera,
and remove the battery covers.
2
Insert a AA battery into each end of the camera, with the
positive pole facing outward.
3
On each battery cover, verify the gasket is clean and fully
seated in the groove.
4
For each battery cover, place the cover into the camera,
press it tightly into the camera, and rotate it toward the back
of the camera to lock it into place.
NOTE: Although the battery covers are interchangeable, it is
recommended to install the covers as shown in the
illustrations.
NOTICE
The camera is not water resistant if the gaskets are not clean
and properly seated, and the covers are not properly locked
into place.
5
Verify each cover is fully sealed and no part of either gasket
is protruding between the cover and the camera.
Installing the Camera in the Mount
1
Place one side of the camera into the mount, with the lens
facing outward.
2
Press the other side into the mount until it clicks.
3
Pull gently on the camera to verify both sides are locked into
the mount.
Pairing the Camera with a Garmin
Navigation Device
You can pair the camera with a compatible Garmin navigation
device. For more information about compatible Garmin devices,
go to the product page at garmin.com/bc40.
1
Update your navigation device to the latest software.
Your device may not support the BC 40 camera without the
latest software. For more information about updating the
software, see the owner's manual for your navigation device.
2
Install batteries in the camera.
The camera enters pairing mode automatically, and the LED
flashes blue while the camera is in pairing mode. The camera
remains in pairing mode for five minutes. If pairing mode
expires, you can remove and reinstall the batteries.
3
Bring the compatible Garmin navigation device outside your
vehicle and within 1.5 m (5 ft.) of the camera, and turn on the
navigation device.
The device detects your camera automatically and prompts
you to pair with it.
4
Select Yes.
TIP: If the navigation device does not detect the camera
automatically, you can select Settings > Wireless Camera >
Add New Camera to pair with it manually.
The device pairs with your camera, and the guidance line
configuration screen appears.
5
Use the on-screen arrows to position the guidance lines, and
select (Aligning the Guidance Lines, page 5).
If the camera or vehicle is not ideally positioned to complete
the guidance line alignment, you can complete the alignment
later from the camera settings.
6
Enter a name for the camera (optional).
You should use a descriptive name that clearly identifies the
location of the camera.
7
Select Done.
Pairing the Camera with a Garmin Navigation Device 3
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin BC 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin BC 40 in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin BC 40

Garmin BC 40 User Manual - German - 14 pages

Garmin BC 40 User Manual - Dutch - 14 pages

Garmin BC 40 User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info