691049
5
Zoom out
Zoom in
Previous page
1/14
Next page
Introduction
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
These installation instructions do not apply to a specific vehicle
type, and are meant as a guide when installing this product on
your vehicle. For questions specific to your vehicle, you should
contact the vehicle manufacturer.
Installation
Vehicle Mount Installation for North America
Installing the Mount on Your Vehicle
1
Remove the license plate screws from the rear of your
vehicle, and remove the license plate, vanity frames, and
license plate covers.
NOTE: The camera mount is intended to be installed onto the
bare license plate, and it is not compatible with vanity frames
or license plate covers.
2
Slide the metal bracket over the top or bottom of the license
plate.
The flat metal plate on the bracket slides behind the
license plate.
NOTE: It is recommended to install the camera above the
license plate, if possible. If there is not enough room above
the license plate on your vehicle, you can configure the
mount for installation below the license plate (Installing the
Camera at the Bottom of Your License Plate, page 1).
3
Hold the license plate and mount up to the license plate area
on your vehicle, and slide the mount up or down to align one
set of mounting holes with the holes in the license plate.
You should use the mounting position that fits your vehicle
and covers the smallest portion of the license plate. You must
avoid covering any text or numbers on the license plate.
Some jurisdictions prohibit covering any portion of the license
plate. It is your responsibility to follow license plate mounting
regulations.
4
Insert the license plate screws through the top of the license
plate and mount, and into the license plate mounting holes on
your vehicle.
5
Fully tighten the license plate screws.
6
Install license plate screws through the bottom holes of the
license plate, and tighten (optional).
This option is not available for all vehicles or for all mounting
bracket positions.
Installing the Camera at the Bottom of Your License
Plate
To allow for proper camera angle adjustment, the Garmin
®
logo
on the camera clip must be right-side up when the mount is
installed on your vehicle. Out of the box, the camera mount is
assembled for installing the camera at the top of your license
plate. When installing the camera at the bottom of your license
plate, you must remove, rotate, and reattach the camera clip.
This allows you to properly adjust the camera angle.
1
Using a Phillips screwdriver, fully loosen the two camera clip
screws , and remove the camera clip from the metal
bracket.
2
Rotate the camera clip 180 degrees, so the Garmin logo is
facing right-side-up.
3
Insert the two camera clip screws into the holes labeled
BOTTOM OF PLATE .
Introduction 1
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin BC 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin BC 40 in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin BC 40

Garmin BC 40 User Manual - German - 14 pages

Garmin BC 40 User Manual - Dutch - 14 pages

Garmin BC 40 User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info