724644
15
Zoom out
Zoom in
Previous page
1/20
Next page
47.1cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 61705 • 08/2018 • FCS4800A
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
47.1cc Petrol Chainsaw
MODEL: №. 61705 • 08/2018 • FCS4800A
26 27
Bucking (Fig AK)
Bucking is cutting a log into lengths for easier
handling.
To saw a log lying on the ground, rst saw
halfway, then roll the log over and cut from the
opposite side. To saw the end of a log supported
o the ground, rst saw up from the bottom
one-third through the log then nish by sawing
down from the top. To saw a log in the middle of
two supports holding it o the ground, rst saw
down from the top one-third through the log
then nish by sawing up from the bottom.
CAUTION: Avoid cutting into the ground as
this will very quickly dull the saw chain.
Pruning (Fig AL)
Pruning is the removal of a limb or branch from a
standing tree.
WARNINGS: Do not use an unstable
foothold or ladder. Do not overreach.
Do not saw above shoulder height. Always use both hands to hold the
chainsaw. First cut up from the bottom and nish down from the top.
1
2
1
2
1
2
1
2
AK.
1
2
1
2
1
2
1
2
AL.
1. Clear the area around the tree and make sure that you have a good foothold
and clear retreat path.
2. Ensure that others in the area are aware of the felling and ensure people and
animals are well clear.
3. Make a notch cut one-third of the way into the tree on the felling side.
4. Make the felling cut on the opposite side to the initial notch and slightly
higher than the notch. As the felling cut gets close to the notch cut, the tree
will begin to fall.
5. Remove the chainsaw from the cut, and stop the engine with the on/o
switch (4), put the chainsaw down and leave the area along the retreat path.
Limbing (Fig AJ)
Limbing is the process of removing the
branches from a fallen tree.
Check the direction in which a branch will
bend before cutting it. Always cut on the op
-
posite side to the bending direction so that
the guide bar (19) is not pinched in the cut.
For large limbs that cannot be removed in
one cut, make an initial cut from the bent
side and nish by sawing from the opposite
direction.
Do not remove limbs that are supporting the fallen tree on the ground until the
tree has been cut into lengths.
WARNINGS: Always keep a balanced stance. Do not stand on the log.
Be alert to the fact that the log may roll over. When working on a slope,
always stand on the uphill side of the log.
1
2
1
2
1
2
1
2
AJ.
Operation Operation
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline FCS4800A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline FCS4800A in the language / languages: English as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info