724645
9
Zoom out
Zoom in
Previous page
1/19
Next page
24.5cc 4 Stroke Petrol Blower Vacuum
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. EBV245A • 08/2018 • 52754
(toll free)
AFTER SALES SUPPORT
(toll free)
24.5cc 4 Stroke Petrol Blower Vacuum
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. EBV245A • 08/2018 • 52754
14 15
Preparation of the Blower Vacuum prior to use
The petrol blower vacuum requires some assembly prior to use. This includes
joining of the vacuum tubes, joining of the blower tubes, and depending if
the tool is to be used for blowing or vacuuming, tting of the tube assembly
to the housing and tting the collection bag assembly to the housing.
Setting up for use as a Blower
IMPORTANT. Blower tube installation aects both blower balance and
performance.
WARNING. Danger from rotating impeller!
Stop the engine before installing or removing the blower tubes.
Never perform any maintenance or assembly procedures on this
machine while the engine is running.
Attaching the Blower Tube
1. Place the blower upright on the ground or on a sturdy work surface (Fig A).
2. Push the blower tube nozzle tube (6) over the upper blow tube (5), lining
up both the arrows on the each tube and lining up the protruding locking
pin/s on the end of the upper blow tube (5) with the protruding channel/s
on the blow tube nozzle (6) (Fig B).
NOTE: You may need to loosen the screw from the blow tube nozzle (6) so
the screw sits ush otherwise the tubes will not connect properly due to the
screw impeding the connection. This is a non-removable screw.
3. Rotate the blow tube nozzle (6) clockwise on the upper blow tube (5)
locking it into place. Then using the spark plug spanner / combination
screwdriver (25),screw in the assembly screw until secure.
4. Loosen the screw (with 2 small washers) from the
discharge port (24), using the supplied spark plug
spanner / combination screwdriver (25). Align and
push the assembled blower tube assembly over the
discharge port (24) on the blower outlet lining up
the arrow on the discharge port with arrow on the
tube and then rotate clockwise until it locks in place
and the screw hole can be seen (Fig C).
5. Using the supplied spark plug spanner /
combination screwdriver (25), screw in the
assembly screw + 2 small washers until secure
(Fig D).
Check the intake cover (8). For use of the blower
vacuum as a blower, the vacuum tubes should
not be tted, but the intake cover MUST be
closed and secured (Fig E).
The blower vacuum is now ready for use as a
blower.
NOTE: The vacuum tubes (9/11) and the
collection bag (10) are not required for the
blower operation.
Setting up for use as a Vacuum
Assembly of the Vacuum tubes
1. Align the upper vacuum tube (9) and the
vacuum tube nozzle (11) so that the protruding
pins on the upper vacuum tube (9) align with the
protruding channels on the vacuum tube nozzle
(11).
NOTE: You may need to loosen the screw from
the vacuum tube nozzle (11) so the screw sits
ush otherwise the tubes will not connect
properly due to the screw impeding the
connection.
2. Slide the upper vacuum tube (9) inside the
vacuum tube nozzle (11) until it will enter no
more, then rotate the vacuum tube nozzle (11 in
an anti clockwise direction until securely locked
together (Fig F). This is a non-removable screw.
3. Using the supplied spark plug spanner /
combination screwdriver (25), secure in the
assembly screw and rotate in a clock wise
direction until secure (Fig G).
D.
G.
F.
E.
TIGHTEN
TIGHTEN
TIGHTEN
Assembly Assembly
Assembly
LOCK IN PLACE
C.A. B.
LOCK IN PLACE LOCK IN PLACE
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline EBV245A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline EBV245A in the language / languages: English as an attachment in your email.

The manual is 0,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info