782039

Gardenline CSP41 Manual

25
Zoom out
Zoom in
Previous page
1/53
Next page
• The working environment around the tree should be cleared so you have secure
footing.
• The machine operator should always be positioned at a higher level in the
working area because the tree will probably roll or slide down after felling.
The following conditions can inuence the tree‘s falling direction:
• Wind direction and speed
• Leaning of the tree - The leaning direction cannot always be recognised
because of uneven or sloping ground. Determine the leaning direction of the
tree using a plumb line or a level.
• Branches growing (and therefore weight) only on one side
• Surrounding trees or obstacles
Look out for destroyed or decayed parts of the tree. If the trunk is decayed, it
can suddenly break and fall on you. Make sure there is sufcient space for the
falling tree. Keep a distance of 2½ tree lengths to the next person or other objects.
The sound of the motor can drown out warning cries.
Remove dirt, stones, loose bark, nails, brackets and wire from the sawing area.
m Ensure you have a free escape route (Fig. A)
Position 1: Escape route
Position 2: Falling direction of the tree
Felling of large trees (from 15cm diameter) - only with relevant training
The undercutting method is used for felling large trees. For this, a wedge is cut out
from the side of the tree according to the required falling direction. After the
dropping cut has been made on the other side of the tree, it will fall in the direction of
the wedge cut.
m NOTICE
If the tree has large prop/buttress roots, these should be removed before the wedge
is cut. If the saw is used for removing the prop/buttress roots, the saw-chain should
not touch the ground so the chain does not become blunt.
Undercut and felling the tree (Fig. B-C)
• For the undercut, rst cut the upper part (Pos. 1) of the wedge (Pos. 2). Cut 1/3
of the way into the tree. Then saw the lower part (Pos. 3) of the wedge (Pos. 2).
AFTER SALES SUPPORT 29
00800 4003 4003 aldi.service.uk@scheppach.com
MODEL: CSP41 PRODUCT CODE: 64055 04/2017
Petrol chainsaw 41cc Safety regulations
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline CSP41 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline CSP41 in the language / languages: English as an attachment in your email.

The manual is 6.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info