781774

Fuxtec FX-KSP250 Manual

38
Zoom out
Zoom in
Previous page
1/99
Next page
Original manual for petrol chainsaw FX-KSP series
◼ Pull the starter handle until the engine
starts.
◼ Engine starts:
− Chainsaw runs at idling speed
◼ Engine does not start:
− Repeat starting procedure until engine
starts.
◼ Slowly and surely lift the chainsaw up off
the ground. Do not touch the throttle trig-
ger when doing this!
◼ With the left hand, pull the front hand
guard (chain brake lever) towards the front
handle and, in doing so, release the chain
brake.
− The saw chain can now run freely on
the guide rail.
CAUTION!
Actuate the throttle trigger (8) only after the
chain brake has been released. The clutch
could otherwise be damaged.
◼ The throttle trigger can now be actuated.
◼ Before starting to saw, check the chain lu-
brication.
− To do this, place the chainsaw against
a light background and open the throttle
fully.
− If a slick of chain oil can be seen on the
light background (e.g. sheet of paper),
the chain lubrication is set correctly.
The chainsaw is ready for operation.
Stopping the engine
◼ Turn the On/Off switch to the "0" position.
CAUTION!
Risk of injury!
Before switching off the chainsaw, always
allow the engine to die down!
Warm start
CAUTION!
The chainsaw is fitted with an Easy-Start
system. Do not pull the start handle quickly
or suddenly.
◼ Block the chain brake using the front hand
guard. To do this, push the front hand
guard forwards until it is heard to engage.
◼ Turn the stop switch to the "I" position (9).
◼ Place the chainsaw on even ground and
secure. Step into the handle recess with
the right foot to do this.
CAUTION!
Before starting the engine:
When placing on the ground to attempt to
start the engine, ensure that the saw chain is
not in contact with the ground.
If there is ground contact while the engine is
being started there is an acute risk of acci-
dent!
Components of the chainsaw could be dam-
aged beyond repair.
◼ Secure the chainsaw with the left hand on
the front handle.
◼ Pull out the chainsaw's starter handle (11)
on the cable until a resistance is felt. Then
continue to pull out in doses.
◼ Engine starts:
− Chainsaw runs at idling speed
◼ Engine does not start:
− Repeat starting procedure until engine
starts.
◼ Slowly and surely lift the chainsaw up off
the ground. Do not touch the throttle trig-
ger when doing this!
◼ With the left hand, pull the front hand
guard (chain brake lever) towards the front
handle – the chain brake can be heard to
disengage.
− The saw chain can now run freely on
the guide rail.
◼ The throttle trigger can now be actuated.
The chainsaw is ready for operation.
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fuxtec FX-KSP250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fuxtec FX-KSP250 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info