450995
92
Zoom out
Zoom in
Previous page
1/119
Next page
92
GOAL of EXAMPLE: STEPS: INPUTS:
Learn how to operate
HOVERING PITCH
and
HOVERING THROTTLE
. See p. 104.
Notice at half throttle, the VR(C) dial
adjusts the throttle separately from the
pitch. VR(A) adjusts the pitch separately
from the throttle.
for 1 second.
(If
ADVANCE
, again.)
C
to
SERVO
.
throttle to center
VR(C) VR(A) center dials.
%H VXUH WRIROORZ \RXUPRGHO¶V LQVWUXFWLRQVIRU SUHÀLJKW FKHFNVEODGH WUDFNLQJHWF 1HYHUDVVXPH DVHW RIEODGHV DUH
properly balanced and will track without checking.
Check receiver battery voltage! Always check voltage with a voltmeter prior to each and every engine start.(Never
DVVXPHEHLQJSOXJJHGLQDOOQLJKWPHDQV\RXUUDGLRJHDULVUHDG\WRÀ\,QVXI¿FLHQWFKDUJHELQGLQJVHUYROLQNDJHV
and other problems can result in a dangerous crash with the possibility of injury to yourself, others and property.
&RQ¿UPWKHVZDVKSODWHLVOHYHODWWUDYHO$GMXVWDUPVLIQHHGHG
Apply full collective and check that the swashplate remained level and there is no binding. Repeat for full cyclic pitch and
roll. If not, adjust as needed to correct in
END POINT
: see p. 39.
Important note: prior to setting up throttle hold, idle-ups, offsets, etc, be sure to get your normal condition operating
properly.
Checking setup prior to going airborne: Check voltage! Then, with the assistance of an instructor, and having completed
all range checks, etc, gradually apply throttle until the helicopter becomes “light on the skids.” Adjust trims as needed to
correct for any roll, pitch, or yaw tendencies. If the tail “wags,” the gyro gain is too high. Decrease gyro gain.
Where next? (Other functions you may wish to set up for your model.)
THROTTLE HOLD
: P. 99.
SUB-TRIM
p. 49 and separate trims for conditions (
OFFSETS
): p. 102.
Governor setup: p. 108.
IDLE-UP
p. 101.
DELAYs
to ease servo response when switching idle-ups: p. 103.
Rudder-to-throttle and other programmable mixes p. 68.
1
Periodically move the throttle stick to full and back down to ensure proper servo settings.
2
It is critical that dials A and C be centered when the pitch and throttle curves are setup.
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T10 CAG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T10 CAG in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info