450995

Futaba T10 CAG Manual

91
Zoom out
Zoom in
Previous page
1/119
Next page
91
GOAL of EXAMPLE: STEPS: INPUTS:
Reverse servos as needed for proper
control operation. Ex: LEFT RUDDER
STICK results in leading edge of tail
rotor blades moving left. Reverse to
operate properly. P. 38.
In the
BASIC
menu, open
REVERSE
.
C
to
REVERSE
.
to choose
REVERSE
.
Choose desired servo and reverse its
direction of travel. (Ex: reverse rudder
servo.)
C
to
CH4:RUDD
.
so
REV
is highlighted.
Are you sure?
Displays.
for 1 second.
Repeat as needed.
to return to
BASIC
menu.
Adjust Travels as needed to match
model's recommended throws (usually
listed as high rates).P. 39.
In the
BASIC
menu, choose
END POINT
.
C
to
END POINT
.
to choose
END POINT
.
Adjust the servos’ end points.
(Ex: elevator servo)
Return to
BASIC
menu.
C
to
ELEV
.
ELEVATOR STICK.
until up travel is as desired.
ELEVATOR STICK.
until down travel is as desired.
Repeat as needed.
Activate
THR-CUT
. P. 98. Open
THROTTLE-CUT
function.
C
to
THROTTLE-CUT
.
to choose
THR-CUT
.
Activate the function. Choose desired
switch and position to activate.
C
to
MIX
to
OFF
.
C
to
SW
. to
C
.
C
to
POSI
. to
DOWN
.
With THROTTLE STICK at idle, adjust
the rate until the engine consistently
shuts off, but throttle linkage is not
binding.
1
Close.
C to down position.
THROTTLE STICK.
C
to
RATE
. until shuts off.
Set up throttle curve for normal. (Usually
changes will not need to be made prior
WR¿UVWÀLJKW3
Open the
THR-CURV/NOR
function.
Adjust if needed.
Close the function.
C
to
THR-CURV/NOR
. .
C
to
1 >
.
to
5%
.
C
to next point.
Repeat.
Set up collective pitch curve for normal
ÀLJKW:HVXJJHVW D VWDUWLQJSRLQW RI 
center of +5,end of +8 to +10 degrees of
blade pitch for aerobatics.
2
(If just learning
WRÀ\DVN\RXULQVWUXFWRU3
Open the
PIT-CURV/NOR
function.
Adjust each point to match desired
FXUYH([¿UVWSRLQW
8%
.)
Close the function.
C
to
PIT-CURV/NOR
. .
C
to
1 >
.
to
8%
.
C
to next point.
Repeat.
Set up revo. mixing for normal. (For
heading-hold gyros, inhibit revo.) P. 97.
Open the
REVO./NOR
function.
Adjust to your desired starting point.
(Ex:
10%
.)
Close the function.
C
to
REVO./NOR
. .
C
to
1 >
.
to
10%
.
C
to next point.
Repeat.
&RQ¿UP*\URGLUHFWLRQ1RWHLIXVLQJ
DKHDGLQJKROG$9&6J\URXVHWKH
GYRO
programming for proper setup.
See p. 106.)
With radio on, move helicopter’s tail to the right by hand.
The gyro should give right rudder input (leading edge of the tail rotor blades
move left).
If the gyro gives the opposite input, reverse direction on the gyro unit itself.
… 91 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T10 CAG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T10 CAG in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info