450995

Futaba T10 CAG Manual

13
Zoom out
Zoom in
Previous page
1/119
Next page
13
NOTE: If you need to remove or replace
the transmitter battery, do not pull on its
wires to remove it. Instead, gently pull on the
FRQQHFWRUV SODVWLF KRXVLQJ ZKHUH LW SOXJV LQWR
the transmitter.
Battery connector location
Charging jack
Trainer function
connector
Battery cover
NT8S
Ni-Cd battery
pack
SWITCH ASSIGNMENT TABLE
• The factory default functions activated by the switches and knobs for a 10CAG Mode 2 transmitter are shown below.
• Most 10CG functions may be reassigned to non-default positions quickly and easily.
• Basic control assignments of channels 5-10 are quickly adjustable in
AUX-CH
(see p. 46). For example, the channel 5
servo, which defaults to SWITCH E for retract use, can easily be unassigned (NULL) to allow for easy use as a second
rudder servo in a mix, or to a slider or dial for bomb door or other control.
• Note that most functions need to be activated in the programming to operate.
• 10CAG Mode 1, 10CHG, and 10CG transmitter functions are similar but reverse certain switch commands. Always
check that you have the desired switch assignment for each function during set up.
Switch/Knob
A or H
Airplane (
ACRO
) Sailplane/Glider (
GLID
) Helicopter (
HELI
)
SWITCH A elevator dual rate
ch10
elevator dual rate
GRZQ EXWWHUÀ\RQ
ch10
elevator dual rate
ch10
SWITCH B rudder dual rate
ch9
rudder dual rate
ch9
rudder dual rate
ch9
SWITCH C up =
ELE-FLP
on
FHQWHUGRZQ
IDLE-DOWN
down =
AIRBRAKE
on
up =
ELE-FLP
on
center = Distance cond.
down = Landing cond.
governor
SWITCH D aileron dual rate aileron dual rate aileron dual rate
SWITCH E or G* ODQGLQJJHDUFK WKURWWOHKROGFK
SWITCH F or H* VQDSUROOWUDLQHU trainer WUDLQHU
THR-CUT
SWITCH G or E* none up = Speed cond.
down = Start cond.
idle-up 1 and 2
SWITCH H or F* none LGOHXSJ\UR
KNOB A ÀDSFK
ÀDSWULPLI
FLAPERON
on)
ÀDS
ch6
HOVERING PITCH
KNOB B ch 8 ch 8 ch 8
KNOB C VSRLOHUFK
(disabled if
AIL-DIFF
on)
ch 7
(disabled if
AIL-DIF
on)
HOVERING THROTTLE
ch7
SLIDER D none ch 5 none
SLIDER E none none
HI-PIT
*On the 10CAG Mode 2 transmitters, the TOP LEFT SWITCHES are spring-loaded and 2-position; on the 10CAG Mode 1, 10CHG, and 10CG,
those switches are on the right side. For consistency, the switch position’s designation remains the same (upper left is F, etc), but the functions are
moved to match the switch type.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T10 CAG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T10 CAG in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info