747917

Futaba T-16IZ Manual

197
Zoom out
Zoom in
Previous page
1/228
Next page
197
→ GO to TABLE OF CONTENTS
FlightTuneExpert（Aileron/ElevatorGyroExpertSetting）FlightTuneExpert（Aileron/ElevatorGyroExpertSetting）
The
"
Flight Tune Expert
"
menus allow further renement of cyclic gyro performance.
"
Flight Tune Expert
"
screen
from the
"
EXPERT MENU 3D
"
screen.
(1) HeadHld A / HeadHld E: Head hold aileron / elevator
This features is used to adjust the heading hold aspect of the gyro control.
If the helicopter is not holding angle or cyclic control rates, increasing the
heading hold gain will improve holding the helicopter at a certain angle and
improve the cyclic rate consistency. If this is set too high you could see an
oscillation on that axis. Lowering the heading hold below default would be
used if the transmitter gain is reduced and a consistent oscillation is still
not fixed during flight.
Settingranges:0~200%Initialvalue:80%
(2) StopTune A : Stop tune aileron
Cyclic stop tuning on the aileron axis. If the helicopter continues to coast
after an after an ail roll, lowering "StpTune A" will create a harder stop action
to remove the coasting. If the helicopter bounces on the aileron axis after an
aileron control input, increasing "StpTune A" will reduce this bounce.
Settingranges:0~250%Initialvalue:80%
(3) StopTune E: Stop tune elevator
Cyclic stop tuning on the elevator axis. If the helicopter, after an elevator
flip, continues to coast, lowering "StopTune E" will create a harder stop
action to remove the coasting. If the helicopter continues to coast after an
elevator flip, lowering the "Stop tune E" will reduce this bounce.
Settingranges:0~250%Initialvalue:80%
(4) HeadResp: Head Response
Head Response matches the gyro control speed to that which the heli-
copter is capable of reacting. In a standard helicopter a Head Response
of 1 should always be used, but on some scale applications, or uniquely
designed rotor heads, increasing head response might be needed to cure
over correction of the gyro.
Settingranges:1~10Initialvalue:1
(5) DeadBand: Dead band
Transmitter control dead band. If you are noticing inconsistent swash plate
drift or poor initialization it could be poor transmitter potentiometer resolu-
tion. If you have to increase this value beyond 10.0, it is best to check
calibration on your transmitter.
Settingranges:0~25Initialvalue:4.0
Cond
Cond
Cond
Cond
(6) RESET : FLT tune data reset
This resets the "FLT.Tun" setting back to the defaults.
… 197 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info