747917
190
Zoom out
Zoom in
Previous page
1/228
Next page
190
GO to TABLE OF CONTENTS
GovernorBasicGovernorBasic
This menu sets the governor’s fundamental functions. The menu Servo limit point set-
ting must be set rst.
"
Governor Basic
"
screen from the
"
BASIC MENU
"
screen.
Note: When using the governor function, be sure
to make each setting of "Governor Basic".
Note: After completing the linkage of the throttle,
be sure to set the "Servo limit point setting" first,
and then set the other functions.
(1) Governor: Governor active
Set the governor operation mode of CGY. The initial setting is "ACT (active)"
where, as the designation implies, the governor is active. If you do not want
to use governor, select "INH (Inhibit)".
Setting:ACT(Active)/INH(Inhibit)Initialsetting:ACT
(2) Gear Ratio:
Input the main rotor gear ratio by pushing the "Gear Ratio" button to select
the desired working mode.
Settingranges:1.00~50.00
tInitialvalue:8.00

t
Notes:
If the gear ratio is not properly set, the
set speed and actual engine speed will
be different.
The gear ratio should be given in the
helicopter instruction manual. If the
helicopter instruction manual does not
give the gear ratio, calculate the gear
ratio as follows:
Rotor
main gear
N1
Engine
pinion gear
N2
Gear ratio = N1/N2
Carry values less than 1/1000 to the
next whole number.
(3) Pole Num.: Pole number
This parameter is used when using a direct phase sensor attachment to a
brushless motor lead. Input the motor pole count as specified by the brush-
less motor manufacturer. When using any revolution sensor other than a
direct phase sensor type, set the pole number to 2
p.
Note: For nitro use, set to 2
p.
Note: The input signal range of the CGY is 0.0
v - 3.0
v. Exceeding this volt-
age range may cause damage to the CGY.
Settingranges:2-24
PInitialvalue:2
P
(4) Servo Type
Select the throttle servo type. Digital servos offer the best response.
Setting:Analog/DG:1520Initialsetting:Analog
WARNING
The servo type parameter within the CGY must match the type of
servo you are using. Incorrect settings may damage the CGY or the
servo. An incorrect setting may also result in the loss of control during
flight.
(5) RPM set.: RPM setting
Setting the main rotor RPM. This is calculated by engine revolution with
the gear ratio of the main shaft.
When the rotation speed can be set with the governor mixing function of
the transmitter, it is necessary to first match the display rpm value of 1-2-3
of "RPM Set" with the display rpm value of the transmitter.
Settingranges:off/700~4,000
rpmInitialvalue:1,000

rpm
*Tosetlowerthan1,000
rpm,set"Low.Revo"of"GovernorExpert"menuto700

rpm.
190


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info