747922
168
Zoom out
Zoom in
Previous page
1/183
Next page
168
Model Menu (Helicopter Functions)
Governor
When using a Futaba governor, this function is
used to switch the RPM of the helicopter's head.
Up to 3 rates can be set for each condition.
*The governor is used by connecting the governor speed
setting channel to CH7 (initial setting).
*When using an independent governor [ON]/[OFF] switch,
connect the AUX([ON]/[OFF]) connector of the governor to
CH8 (initial setting) and set the switch to CH8 (Governor2)
at the Function menu of the Linkage menu.
*When using the Fuel Mixture function, the mixture servo
is controlled from the governor. When transmitting the
mixture curve data from the transmitter to the governor, the
governor AUX (m.trm) connector must be connected to CH8
(initial setting) and governor side setting performed. See the
governor instruction manual.
Note: Always set (Control) and (Trim) to [--] for
[Governor] and [Governor2] of the Function menu
of the Linkage menu.
ŏ Select [Governor] at the model menu
and call the setup screen shown below.
Fine tuning VR settings
RPM adjustment
Unit display selection:
[%] [rpm]
Setting method
ƔActivate the mixing
When using this function, Tap [INH]. (ON is
displayed.)
*When the function is set ON/OFF at the governor setup
screen, the governor rpm setting channel end point servo
travel and limit point are now initialized.
*When changed from INH to ACT (ON), the servo travel is
initialized to 100 and the limit point is initialized to 155.
*When operation is changed to INH at all conditions, the
servo travel is initialized to 100 and the limit point is
initialized to 135.
ƔRPM adjustment
Tap to the rate item .
Adjust the rpm using the "ʈʈ" "ʈ" "ʆ" "ʆʆ"
buttons.
Initial value: 50 (1500rpm)
Adjustment range: OFF, 0~110 (OFF,
700~3500rpm)
*When the value is tapped reset to the initial value.
ƔUnit display selection
Tap to the UNIT item [] [rpm]. Select the
unit.
ŏReturn to Model menu
168


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX36 in the language / languages: English as an attachment in your email.

The manual is 11,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba FX36

Futaba FX36 User Manual - German - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info