747922
45
Zoom out
Zoom in
Previous page
1/183
Next page
45
Model Basic Setting Procedure
ŘőŃŬƇƏƈŃƇƒƚƑŃƖƈƗƗƌƑƊ
The idling speed can be lowered with one touch by
a switch without changing the throttle trim position.
Perform this setting with the Idle down function of the
Linkage menu. After activating the Idle down function
and selecting the switch, adjust the idle down speed. For
safety, the idle down function acts only when the throttle
stick is slow side.
*While the Throttle cut function is in operation, the Idle down
function does not work.
řőŃŤũŵŃŋŧŒŵŌ
AFR function is used to adjust the throw and operation
curve of the stick, lever, and switch functions for each
flight condition. This is normally used after End point
has de¿ned the maximum throw directions.
ŚőŃŤƌƕƅƕƄƎƈ
This function is used when an air brake is necessary
when taking off or diving, etc.
The preset elevators and Àaps (camber Àap, brake Àap)
offset amount can be activated by a switch.
The offset amount of the aileron, elevator, and flap
servos can be adjusted as needed. Also the speed of the
aileron, elevator, and flap servos can be adjusted. (In
side/Out side) A delay can be set for each condition,
and a cut switch which will turn OFF the delay can be
chosen. Trim amounts can be ¿ne-tuned by setting a VR.
You can also set the auto mode, which will link Airbrake
to a stick, switch, or dial. A separate stick switch or dial
can also be set as the ON/OFF switch.
śőŃŤƇƇƌƗƌƒƑŃƒƉŃƳƌƊƋƗŃƆƒƑƇƌƗƌƒƑƖ
The Condition select function automatically allocates
the Condition 1 for each model. Condition 1 is the
default condition and is the only one active when a new
model type is de¿ned.
If you want to add Àight conditions, please refer to a
description of the Condition select function.
*The Condition 1 is always on, and remains on until other
conditions are activated by switches.
*When a new condition is added, the model data of the
Condition 1 is automatically copied to the new condition.
*You can set the model data of new condition in the switch
ON state. However, if the group mode (Gr) was selected in
advance, the same data will be input at all the conditions.
Select the single mode (Sngl) and adjust only the condition
you want to change. For Group/Single mode switching, refer
to the description at the back of this manual.
*The Condition delay can be programmed for each channel.
The Condition delay is used to change the servo throw
smoothly when switching conditions.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX36 in the language / languages: English as an attachment in your email.

The manual is 11,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba FX36

Futaba FX36 User Manual - German - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info