747921

Futaba FX22 Manual

45
Zoom out
Zoom in
Previous page
1/174
Next page
45
<Model Basic Setting Procedure>
5. Throttle/Pitch curve setting
This function adjusts the throttle or pitch
operation curve in relation to the movement of the
throttle stick for each condition.
7KURWWOHFXUYHVHWWLQJH[DPSOH!
Activate the throttle curve of each condition with
the condition select switch.
ŏNormal curve adjustment
Normal curve creates a basic throttle curve
centered near hovering. This curve is adjusted
together with the pitch curve (Normal) so that the
engine speed is constant and up/down control is
easiest.
ŏIdle up curve adjustment
The low side Throttle curve creates a curve
matched for aerobatics (loop, roll, 3D, etc.).
ŏThrottle hold curve adjustment
ConÀrm that the rate of the slowest position (0) of
the stick is 0 (initial setting).
<([DPSOHRISLWFKFXUYHVHWWLQJ!
Activate the pitch curve of each condition with
the condition select switch.
ŏPitch curve (Normal)
Make the pitch at hovering approximately 5
º
~6
º
.
Set the pitch at hovering with the stick position at
the 50 point as the standard.
*Stability at hovering may be connected to the throttle curve.
Adjustment is easy by using the hovering throttle function
and hovering pitch function together.
ŏPitch curve (Idle up 1)
The idle up 1 pitch curve function creates a curve
matched to airborne Áight.
Set to -7
º
~12
º
as standard.
ŏPitch curve (Idle up 2)
The high side pitch setting is less than idle up 1.
The standard is 8
º
.
ŏPitch curve (Hold)
At auto rotation, use the maximum pitch at both
the high and low sides.
[Pitch angle setting example]
Throttle hold: -7
º
~12
º
4. Servo Connection
Connect the throttle rudder, aileron, elevator,
pitch, and other servos in accordance with the
kit instruction manual. For a description of the
connection method, see "Receiver and Servos
Connection".
Note: The channel assigned to each function
can be checked at the Function menu of the
Linkage Menu.
ŏ If the direction of operation of the servo
is incorrect, use the Reverse function of
the Linkage Menu. Also use the swash AFR
function in other than the H-1 mode.
ŏ Adjust the direction of operation of the gyro.
(Gyro side function)
ŏ Connect the throttle linkage so that the
carburetor can fully close at full trim throttle
cut.
ŏ Adjust the neutral position at the linkage side
and Àne tune with the Sub-Trim function and
End Point function. To protect the linkage,
a limit position can also be set with the End
Point function.
ŏ Swash plate correction (Except H-1 mode)
*If any interactions are noticed, for a description of the
linkage correction function, please refer to the SWASH
function.
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX22 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info