747921
44
Zoom out
Zoom in
Previous page
1/174
Next page
44
<Model Basic Setting Procedure>
1. Model addition and selection
Initially, the FX-22 assigns the first model to
model-01 in the transmitter. To add new models
or to select a model already programmed, use the
Model Select function of the Linkage Menu.
This is convenient when selecting a model after
entering the model's names in advance. The FX-
22 is capable of storing up to 30 models in the
transmitter's internal memory. Additional models
can also be stored in an optional SD card.
The currently selected model is displayed in
the middle of the screen. Before flying and before
changing any settings, always confirm the model
name.
When a new model is added, the Model Type select
screen and system mode setup screen automatically
appear. Change, or check that they match the swash
type and receiver type of the model used.
When a new model is added, you will need to re-
link the receiver.
2. Model type and swash type selection
If a different model type is already selected,
select helicopter with the Model Type function of
the Linkage Menu, and then select the swash type
matched to the helicopter.
*The Model Type function automatically selects the
appropriate output channels, control functions, and mixing
Helicopter basic setting procedure
This section outlines examples of use of the helicopter functions of the FX-22. Adjust the actual values,
etc. to match the fuselage used.
functions for the chosen model type. Six swash types are
available for helicopters.
*For a description of the swash type selection, refer to the
MODEL TYPE function.
3. Flight condition addition
7KHWUDQVPLWWHURIIHUVXSWR¿YHÀLJKWFRnditions
per model.
The Condition Select function automatically
DOORFDWHV¿YHFRQGLWLRQVIRUKHOLFRSWHUV
(Initial setting)
ŏ NORMAL
ŏ IDLE UP1 (SW-E)
ŏ IDLE UP2 (SW-E)
ŏ IDLE UP3 (SW-F)
ŏHOLD (Hold switch is not assigned initially)
Note: Since you may accidentally activate
a condition that not previously setup during
ÁLJKWZKLFKFRXOGFDXVHDFUDVKZHVXJJHVW
deleting conditions that are not used.
*For a description of the condition deletion, refer to the
Condition Select function.
The NORMAL condition is always on, and
remains on until other conditions are activated by
switches.
The priority is throttle hold/idle up 3/idle up 2/
idle up 1/normal. Throttle hold has the highest
priority.
The Condition Delay can be programmed for
each channel and condition. The Condition Delay
is used to change the servo throw smoothly when
switching conditions.
*HQHUDOÀLJKWFRQGLWLRQVHWWLQJH[DPSOH
ŏ Normal: (Use initial setting conditions/operate
when switch OFF)
Use from engine starting to hovering.
ŏ Idle up 1: (Operate at SW-E center)
Use in stall turn, loop, and other maneuvers.
ŏ Idle up 2: (Operate at SW-E forward side)
Use in rolls.
ŏ Throttle hold: (Operate at SW-G forward side)
Use in auto rotation.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX22 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info