747921

Futaba FX22 Manual

43
Zoom out
Zoom in
Previous page
1/174
Next page
43
<Model Basic Setting Procedure>
throttle stick in the 1/3 or less (slow side) position.
5. Idle down setting (Airplane)
The idling speed can be lowered with one touch
by a switch without changing the throttle trim
position. Perform this setting with the Idle Down
function of the Linkage Menu. After activating the
Idle Down function and selecting the switch, adjust
the idle down speed. For safety, the idle down
function acts only when the throttle stick is in the
lowest part of its throw.
*While the Throttle Cut function is in operation, the Idle
Down function does not work.
6. D/R function
D/R function is used to adjust the throw and
operation curve of the stick functions (aileron,
elevator, rudder and throttle) for each switch
SRVLWLRQDLUSODQHRUHDFKÀLJKWFRQGLWLRQJOLGHU
7KLVLVQRUPDOO\XVHGDIWHUWKHPRGHOHUKDVGH¿QHG
the maximum throw directions in the End Point
settings.
(Airplane)
(Glider)
7. Airbrake (Airplane)
This function is used when an airbrake is
necessary when taking off or diving, etc. Please
note: this menu item is only available under certain
ZLQJFRQ¿JXUDWLRQV)RUH[DPSOHLWZLOOQRWDSSHDU
if a single aileron wing type has been selected.
7KHSUHVHWHOHYDWRUDQGÀDSRIIVHWDPRXQWFDQ
be activated by a switch.
The offset amount of the aileron, elevator, and
flap servos can be adjusted as needed. Also the
VSHHGRIWKHDLOHURQHOHYDWRUDQGÀDSVHUYRVFDQ
be adjusted. You can also set the Auto Mode, which
will link Airbrake to a stick, switch, or dial. A
separate stick switch or dial can also be set as the
ON/OFF switch.
$GGLWLRQRIÀLJKWFRQGLWLRQV*OLGHU
The Condition Select function automatically
allocates the normal condition (NORMAL) for
each model. NORMAL is the default condition and
is the only one active when a new model type is
GH¿QHG
,I\RXZDQWWRDGGÀLJKWFRQGLWLRQVSOHDVHUHIHU
to a description of the CONDITION function.
*The NORMAL is always on, and remains on until other
conditions are activated by switches, stick positions, etc.
Please refer to the section entitled Switch Selection Method
for additional information on how to do so.
*It is possible to customize the activation of the flight
conditions.
*The Condition Delay can be programmed for each channel.
The Condition Delay is used to change the servo throw
smoothly when switching conditions.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX22 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info