30098

Futaba FP8SSHP Manual

20
Zoom out
Zoom in
Previous page
1/36
Next page
H. Servo reversing switches
These switches reverse the direction of the servos.
They are very convenient when connecting the linkage.
Fig.
49
CH8 switch
channel
CH7 lever channel
CH6 pitch control
CH5 switch channel
NORM position
: Forward
REV position
: Reverse
Rudder
Throttle
Elevator
Aileron
I. ATV/FS button
•These two pushbutton switches are used for servo
deflection angle setting of ATV, FS or HOLD func-
tion; servo test start & stop; reset; battery FS memo-
ry
set,
etc.
•USING ATV (Aileron ATV
taken as an example)
1 First, set switch [K] [35] to the ATV side.
2 Next, set CHANNEL
SELECT switch
[J] [34]
to the
1 (aileron) position.
3 Set the transmitter and receiver power switches to
ON, and check the operation of the servos.
4 Set the aileron stick for full right rudder, hold it in
that position, and set the aileron right throw to the
desired angle by
pressing
buttons [33] and [32]
.
5 To set aileron left, hold the aileron stick in the full
left position and set the servo throw with buttons
[33] and [32]
.
(ATV can be adjusted in 64 steps. ATV can be con-
tinuously varied by pressing and holding the but-
ton for more than 1.5 seconds.)
6 For the other channels,
select
the
channel
with
the
CHANNEL SELECT switch [J] [34] and operate
ATV.
7 At the end of adjustment, set switch [K] [35] to the
center OFF position and set switch [J] [34] to OFF
position.
8 This ATV function is memorized
even if the power
switch is set to off, the ATV function
is lost if the
transistor Nicd is fully discharge.
9 When clearing the ATV, set switch [35] to RESET
and switch [34]
to
position 2 and
press
buttons [32]
and [33] simultaneously. ATCs of all channels are
cleared and servos deflect their 100% angle.
[32]This
pushbutton
switch
is
used
when:
1 Making the ATV servo deflection angle larger.
2 Turning the FS function on.
3 Starting the servo test.
—[33] This pushbutton switch is used when:
1
Making the ATV servo deflection angle smaller.
2 Turning the HOLD function on.
3 Stopping the servo test.
When button [32] and [33] are pressed at the same time,
reset or battery FS memory setting is possible. At this
time, lamp [A] of monitor lamps [24] goes out momen-
tarily so that setting can be monitored.
Fig.
51
ATV SETTING
Press button [32] and [33] while
holding the aileron stick in the
full position.
Switch switches [J] [34] and [K] [35]
HOW TO USE FS (Fail Safe)
(Throttle channel as an example.)
1 First, set switch [K] [35]
to
FS SELECT.
2 Set the transmitter and receiver power switches
to
ON, and check the movement of each servo.
3 Next, while switching the channel select switch [34]
from 1 to 8 in order, set the channels to be used
with FS, with button [32] and set the channels to
be used with HOLD, with button [33]. In this ex-
ample, set 3 (throttle) to FS with button [32].
4 Set the throttle lever to the slowest position, and
press
the FS
set
button
[36]
on
the
back
of
the
transmitter.
5 The 1 — 4 above set low throttle for the FS
function. After setting FS function, turn switch
[35] and [34]
to
OFF. Test
fail
safe
by
turning
the
transmitter power switch to OFF.
18
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP8SSHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8SSHP in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info