30098
21
Zoom out
Zoom in
Previous page
1/36
Next page
Each servo moves to the neutral position except
the throttle servo which moves to the slow position
that was just set.
6 Pail safe for all channels can be set with one touch
by setting the sticks and switches of the all channel
to any predetermined position
and
pressing the FS
button [36] one time.
7 The FS function can be set for all channels and any
servo deflection angle in this manner. When using
FS in all channels the function select switch must
be set to the FS ALL position.
8 Since this FS function is memorized by the trans-
mitter which transmits the data every 60 seconds,
even when the receiver power switch is set to OFF,
resetting is unnecessary.
9 After those settings, set switch [35]
to
OFF-to pre-
vent erroneous setting.
10 When button [36] is pressed twice, setting FS in
flight, etc., the servo position of the second is
memorized in FS and transmitted.
11 To clear the preset FS information, set switch [35]
to reset position switch [34] to position 1 and press
buttons [32] and [33] simultaneously. FS of all the
channels is cleared and all the servos move to the
neutral position.
FS function/HOLD function
The FS function is turned on with button [32] and
the
HOLD
function
is
turned
on
with
button [33]
as
previously described.
FS (Fail safe function)
FS is a function which moves the servo of each chan-
nel to a position preset on the transmitter when no
radio waves are received by the receiver from the
transmitter or when continuous strong noise is receiv-
ed for about one second or longer. The set operates
by the hold mode in one second and then, by the FS
mode. When the noise or interference disappears and
normal radio waves are received in approximately one
second, FS is released.
HOLD (Hold function)
HOLD is a function which stops all the servos speci-
fied by
HOLD
(by
button [33]
to
the
last
correct
command immediately before the erroneous signal
was received.
When the noise, interference, etc. disappears and
normal radio waves are received, HOLD is released.
Set the FS function and HOLD function as you like.
•When
switch [35]
is
switch
to
TEST-B. all
the
servos
operate linearly over their full travel. (Channel select
switch [34] in TEST-ALL position at this time.) Only
the servos set at the channel select switch are oper-
ated.
The
servo
test
is
started
by pressing
button [32]
and
is
stopped
by
pressing
button [33].
Fig.
52
BFS MEMORY SETTING
1 BFS (Battery fail safe function) is a function which
moves the throttle servo to a preset position as set
by the FS when there is only a small amount of
power left in the receiver Nicd battery. (If not
set, the throttle servo will be set to medium slow
automatically.)
2 The BFS setting method is the same
as the FS
usage method previously described.
3 To release the throttle servo from the preset posi-
tion
set
by BFS and
regain
control, lower the
throttle lever in the slow direction. When the
throttle lever reaches a certain point, BPS will be
released and the throttle servo can be controlled
for 36 seconds.
4 Setting this throttle lever point is called BFS
memory setting, and is done as follows:
•First, set switch [35] to BFS MEMO.SET and set
switch [34] to position [3] (throttle channel.).
Next, while watching the movement of the servo,
set the throttle lever to the desired position (be-
tween slow and medium slow recommended) and
press buttons [32] and [33] simultaneously. This
completes BFS memory setting.
•This
memory allows
setting
the throttle to any
position, slow
to
high.
•Lamp
[A]
of
monitor
lamps [24]
goes
out
at
the
point where BFS is released, this allows BFS to
be checked.
•When there is little power left in the receiver
Nicd battery, the throttle servo automatically
stops at the position set by BFS, BFS is released
when the throttle lever is moved to the memoriz-
ed point. Throttle can then be controlled for 36
seconds by throttle lever
•When
the
BFS
status
comes
out
during
flight,
immediately lower the throttle lever to release
BFS. then quickly land.
19
•The
operation of the
servos
can
be checked by
set-
ting the transmitter and receiver power switches to
ON.
•When switch [35] is switched to TEST-A, the servos
move half-side first and then, come back to neutral
and repeat the other-half from channel 1 to channel
8. (Channel select switch [34] to TEST-ALL position
at this time.) The servos set by the channel select
switch do not operate. (If set to 5, the landing gear
servo does not operate.)
Function setting can be confirmed by means of lamp
[A] of monitor lamps
[24].
1 When switch
[35]
is at FS SELECT
When lamp [A] is on, HOLD and
when lamp
[A] is
off,
FS.
2 When switch [35] set to ALL FS, off.
3 When switch [35] set to ATV and button [32] or [33]
pressed, blink.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP8SSHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8SSHP in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info