747972

Futaba CGY750 V 2.0 Manual

13
Zoom out
Zoom in
Previous page
1/27
Next page
13
(16) Swash rotation [default: 0 deg] [ranges: -90 deg ~ +90 deg ]
Using the Data (+/-) key electronically add rotor head phasing to the swash plate controls. If possible,
it is recommended to use mechanical phasing adjustment, but if the rotor head does not allow this and
you feel that the model is NOT flying axially on each control input, using this parameter can be used to
adjust the pure reaction of each axis in flight. (Typically advanced phasing on clockwise rotor disk and
a slight clockwise increase in swashplate alignment vs rotor axle are needed to create a axial reaction,
vice versa for a counterclockwise rotor disk model.)
(17) Data reset
This resets all of the Swashplate parameters back to the default values. Press the data [+] key
once, and [Exec ??] is shown as a confirmation. Press the data [+] key again to confirm the op-
eration and all of the gyro parameters will be reset.
SWASH DETAIL MAP
2/2
Rrturn to SWASH EXPERT MAP. 1/2
S
WASH
D
ETAIL
S
ETTING
Push
DATA
+/– key
Push
MODE
+/– key
(15) Speed compensation [default: 50%(H3-120), 0%(except H3-120)] [ranges: 0% ~ 100%]
In 120 degree CCPM all servos do not travel the same distance on elevator input. Having previously
set the ELE-PIT and ELE-AIL parameters, if during FAST movement of the elevator axis the swash
plate is not staying level, use the Data (+/-) key to match all servo speeds (+ will slow the Aileron/Pitch
Servo – will reduce speed comp on Aileron/Pitch Servo)
(14) Compensation direction of the elevator [default: plus]
If the above Data (+/-) correction from 0-100 is NOT in the correct compensation direction, change the
value from PLUS or MINUS using the Data (+/-) key.
Push
DATA
+/– key
(13) Linkage compensation elevator [default: 0%] [ranges: 0% ~ 100%]
At HIGH pitch and LOW pitch check to make sure that the swash plate is staying level on the ai-
leron and collective axis when using elevator inputs. If the swashplate is raising or falling, use the
Data (+/-) key to keep the swash plate position the same as middle during elevator inputs.
NOTE – check all four directions: high/back; high/forward; low/back; low/forward.
Setting the CGY750 gains by using endpoints or manual adjust-
ments
,I \RXU WUDQVPLWWHUGRHV QRW VXSSRUWWKH UHPRWH JDLQDGMXVWPHQW
LWLVVWLOOSRVVLEOHWRXVHVSDUHFKDQQHORQWKHWUDQVPLWWHUWRPDNH
WKHDGMXVWPHQWV$VVLJQXQXVHGFKDQQHOYHULI\WKDW WKHVHFKDQ-
QHOVDUHQRW DVVLJQHGRURSHUDWHGE\ DVZLWFKRUGLDO ZLWKLQWKH
WUDQVPLWWHU 6HWWKH>6%86%DVLF@ ĺ³5RW+G*Q´FKDQQHOV WR
WKHDSSURSULDWHFKDQQHO 8VHWKHHQGSRLQW DGMXVWPHQWZLWKLQ
\RXUWUDQVPLWWHUIRUWKHVHFKDQQHOVWRPDNHWKHJDLQDGMXVWPHQWV
DQGWKH UHYHUVHIXQFWLRQZLWKLQ WKHWUDQVPLWWHU WRVHW WKH PRGH
>$9&6125@&RQGLWLRQVZLWKWKHWUDQVPLWWHUPD\DOVREHXVHG
WRDFKLHYHGLIIHUHQWJDLQVEDVHGXSRQÀLJKWPRGHV3OHDVHUHIHUWR
\RXUWUDQVPLWWHUVLQVWUXFWLRQPDQXDOIRUIXUWKHUGHWDLOV
Manual gain adjustment
,I\RXUVHWXSGRHVQRWOHDYHDQ\FKDQQHOVIUHHRULI\RXUWUDQVPLW-
WHUGRHVQRWVXSSRUWDX[LOLDU\JDLQDGMXVWPHQWWKHQLWLVSRVVLEOH
WRDGMXVWWKHJDLQPDQXDOO\ ZLWKLQWKH&*< 6HW ERWK WKH
>6%86@%DVLFĺ 5RW+G*QWR>,1+@7KHJDLQDGMXVWPHQWV
DUHQRZPDGHE\HQWHULQJWKH>)OLJKW7XQLQJ@ĺ%DVH*DLQDQG
SUHVVLQJWKHGDWD>@RU>@NH\V
: TX Set-up for adjusting cyclic gains via the transmitter.
Using the Remote Gain Functions (roll, pitch and yaw)
6RPH)XWDEDWUDQVPLWWHUVFRQWDLQDX[LOLDU\JDLQ IXQFWLRQVIRU
DLOHURQHOHYDWRU DQG \DZ 3OHDVH UHIHUWR \RXU WUDQVPLWWHUVLQ-
VWUXFWLRQ PDQXDO $VVLJQ WKH *<5 *<5$,/ DQG *<5(/(
FKDQQHOVZLWKLQWKHWUDQVPLWWHU:LWKLQWKH&*< >6%86@
%DVLFPHQXĺ5RWRU+HDG*\UR*DLQ³5RW+G*Q´±,QWKH6%86
PHQXDVVLJQLQJ³5RW+G*1´ WR DFKDQQHOZLOO DOORZ WKH5RWRU
KHDGJDLQ WR EH DGMXVWHGYLD WKH7; ,I \RXDUH XVLQJ D&+ RU
OHVV7;VHWWLQJ³5RW+G*Q´WR³,1+´ZLOOWKHQGHIDXOWWKHJDLQ
WR³%DVH*DLQ´LQWKH)OLJKW7XQLQJPHQX6XJJHVWHGVHWWLQJDQG
GHIDXOWLV&+7DLO5RWRU*DLQ³5*Q´±,QWKH6%86PHQXDV-
VLJQLQJ³5*Q´WR DIUHH7;FKDQQHOZLOO DOORZIRUWKH WDLOURWRU
JDLQ WREH DGMXVWHG YLD WKH7; 6XJJHVWHGVHWWLQJ DQG GHIDXOW LV
&+
7KHJ\URIXQFWLRQZLWKLQ\RXUWUDQVPLWWHUVKRXOGOLVWDOOWKUHHJDLQ
FKDQQHOV$GMXVWPHQWVFDQEH PDGHIURPZLWKLQWKLVIXQFWLRQ
7KHJ\UR IXQFWLRQFDQXVXDOO\ EHDVVLJQHGWRYDULRXVVZLWFKHV
RU FRQGLWLRQV WR RIIHUJUHDWHU DGMXVWDELOLW\ 3OHDVH UHIHU WR \RXU
WUDQVPLWWHUVLQVWUXFWLRQPDQXDOIRUIXUWKHUGHWDLOV
WARNING
Verify that the gyro compensates in the correct direction for all
three axes before flight. If the compensation direction is incorrect,
the model will roll, flip, or pirouette uncontrollably even before it
leaves the ground.
TX A
ILERON /
E
LEVATOR
G
YRO
G
AIN
S
ET-UP
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba CGY750 V 2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba CGY750 V 2.0 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info