747972
12
Zoom out
Zoom in
Previous page
1/27
Next page
12
S
WASH
D
ETAIL
S
ETTING
,WHPV±DUHXVHGWRNHHSWKHVZDVKSODWHOHYHODWKLJKDQGORZFROOHFWLYHSLWFKWRF\FOLFLQWHUDFWLRQVDQGF\FOLFSLWFKWRFROOHFWLYHSLWFKLQ-
WHUDFWLRQV7RHQWHUWKHGHWDLOPHQXQDYLJDWHWRWKH%DVLFPHQXSUHVVDQGKROGWKHPRGH>@NH\IRURQHVHFRQGDQGWKHPHQXZLOOFKDQJHIURPWKH
%DVLFWR'HWDLO7RH[LWWKH'HWDLOPHQXSUHVVDQGKROGWKHPRGH>@NH\IRURQHVHFRQGDQGWKH%DVLFPHQXZLOOEHGLVSOD\HG
SWASH DETAIL MAP
1/2
(1) Swash expert setting: start display
Use the mode [+] or [-] keys to navigate through the menu.
3,7ĺ$,/PL[LQJUDWH>GHIDXOW@>UDQJHVa@
Going from MID to HIGH and MID to LOW collective pitch check that the swash plate is traveling
flat throughout the entire range. Using the (+/-) Data keys to level the swash plate on the aileron
axis to the middle point by raising or lowing the aileron servo.
3,7ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@
Going from MID to HIGH and MID to LOW collective pitch check that the swash plate is traveling
flat throughout the entire range. Using the (+/-) Data keys to level the swashplate on the elevator
axis to the middle swash position by raising or lowering the elevator servo.
$,/ĺ3,7PL[LQJUDWH>GHIDXOW@>UDQJHVa@
At middle collective pitch check that during right to left and left to right aileron action the swash
plate is staying level on the elevator and collective pitch axis. If the swashplate is rising or falling
with aileron inputs, use the Data (+/-) key to raise or lower the swash plate to match the middle
point during aileron inputs.
$,/ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@
This parameter adjusts the aileron to 2nd elevator mixing rate. The rate can be adjusted for left
and right directions individually. It is only available for H4-45 swash mode.
(/(ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@
This parameter adjusts the elevator to 2nd elevator mixing rate. The rate can be adjusted for up
and down directions individually. It is only available for H4 swash mode.
 (/(ĺ3,7 PL[LQJ UDWH >GHIDXOW + H[FHSW +@ >UDQJHV  a
150%]
During back and forward elevator inputs at middle collective, check if the swash plate is raising or
lowering during the input. If it is moving use the Data (+/-) key to raise or lower the swash plate to
match the middle point during elevator inputs.
 (/(ĺ$,/ PL[LQJ UDWH >GHIDXOW + H[FHSW +@ >UDQJHV  a
150%]
While moving the elevator back and forth at middle collective, check to make sure the aileron axis
is staying level. Use the Data (+/-) key to raise or lower to level the swash plate during full forward
and back elevator input.
(11) Linkage compensation aileron [default: 0%] [ranges: 0% ~ 100%]
At HIGH pitch and LOW pitch check to make sure that the swash plate is staying level on the el-
evator and collective axis when using aileron inputs. If the swashplate is raising or falling, use the
Data (+/-) key to keep the swash plate position the same as middle during aileron inputs.
NOTE – check all four directions: high/right; high/left; low/right; low/left
3,7ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@
This parameter adjusts the pitch to 2nd elevator mixing rate. The rates can both be adjusted indi-
vidually for both full high and low collective positions. It is only available at H4 swash mode.
$,/ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@
This parameter adjusts the aileron to elevator mixing rate. The rate can be adjusted for left and
right directions individually. It is only available for H4-45 swash mode.
(12) Compensation direction of the aileron [default: plus]
If the above Data (+/-) correction from 0-100 is NOT in the correct compensation direction, change
the value from PLUS or MINUS using the Data (+/-) key.
Push
DATA
+/– key
Push
MODE
+/– key
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba CGY750 V 2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba CGY750 V 2.0 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info