747972

Futaba CGY750 V 2.0 Manual

11
Zoom out
Zoom in
Previous page
1/27
Next page
11
WARNING
Verify that the CGY750 compensates in the correct direction before flight. If the compensation
direction is incorrect the model will roll and/or pitch uncontrollably at lift off.
S
WASH
B
ASIC
S
ETTING
SWASH BASIC MAP. 2
/
2
(11) Swash ring [default: 130%]
This parameter is used to prevent binding of the swash plate servos when the transmitter control
stick is moved toward a corner (for example, full right and full aft cyclic). Press the Data [+] or [-]
key to adjust the value.
(13) Aileron direction memorizing
This parameter teaches the direction of aileron swashplate movement to the CGY750. Move the
aileron stick to RIGHT full and push the DATA [+] or [-] key. The RIGHT direction of the aileron data
will be saved to CGY750. To confirm the setting, move the aileron stick to full RIGHT, and the “!”
mark will appear on the display. This procedure must be done for the Pirouette and Pitch compen-
sations to function correctly.
(14) Elevator direction memorizing
This parameter teaches the direction of elevator swashplate movement to the CGY750. Move the
elevator stick to full back (pull) and push the DATA [+] or [-] key. The back direction of the elevator
data will be saved to CGY750. To confirm the setting, move the elevator stick to full back, and the “!”
mark will appear on the display. This procedure must be done for the Pirouette and Pitch compen-
sations to function correctly.
(15) Pitch low memorizing [default: 1940μS]
This parameter saves the negative collective pitch point into the CGY750. Move the collective
pitch stick to full negative pitch and push DATA [+] or [-] key. Full negative pitch signal will be saved
to the CGY750. The display shows “!” when the stick is at the saved point. The negative collective
pitch setting must saved into the CGY750 for Pirouette and Pitch compensations and/or linkage
compensation to function correctly
(9) Swash Rate (rate adjustment) [default: 50% ranges: 0~100%]
The Swash Rate settings are used to adjust the amount of throw-based cyclic pitch is allowed for
roll (aileron) and pitch (elevator). The one setting applies to both roll and pitch axes; they are not
individually adjusted. Use the Data [+] or [-] key to make an adjustment.
(DUAL RATES MUST BE 100)
-Suggested amount of base cyclic pitch
●
800 size – 10 degrees
●
700 size – 9 degrees
●
600 - 550 size – 8 degrees
●
500 size 7 degrees
●
450 and below- 6 degrees
(10) Pitch Rate (rate adjustment) [default: 50% ranges: 0~100%]
The [PIT.Rate] is the amount of collective pitch travel allowed. A good starting range for Sport, 3D
and F3C is +/-10 to +/-12 degrees. Use the Data [+] or [-] key to make an adjustment. 50% ranges:
0~100%
(12) Aileron (roll)/ Elevator (Pitch) Gyro direction setting [default: Normal]
This parameter controls which direction the CGY750 (roll / pitch axis) will compensate when the
helicopter rolls (pitches). Pick the helicopter up and roll the helicopter to the right. The CGY750
should compensate by adding left cyclic to the swash plate. (Pick the helicopter up and rotate
the nose of the helicopter downward. The CGY750 should compensate by adding aft cyclic to the
swash plate.) If the CGY750 compensates in the wrong direction, then it will be necessary to re-
verse the Compensation Direction setting by pressing the [+] or [-] data key once.
Push
MODE
+/– key
Push
DATA
+/– key
Push
DATA
+/– key
Push
DATA
+/– key
(17) Pitch high memorizing [default: 1100μS]
This parameter saves the full positive collective pitch point into the CGY750. Move the collective
pitch stick to full positive pitch and push DATA [+] or [-] key. The full positive pitch signal will be
saved to the CGY750. The display shows “!” when the stick is at the saved point. The positive col-
lective pitch setting must saved into the CGY750 for Pirouette and Pitch compensations and/or
linkage compensation to function correctly.
(16) Pitch zero memorizing [default: 1520μS]
This parameter saves the zero collective pitch point into the CGY750. Move the collective pitch
stick to zero degrees pitch and push DATA [+] or [-] key. The zero degrees pitch signal will be
saved to the CGY750. The display shows “!” when the stick is at the saved point. The zero degrees
pitch setting must saved into the CGY750 for Pirouette and Pitch compensations and/or linkage
compensation to function correctly.
When CondMenu is ON, this
changes into CondMenu.
When CondMenu is ON, this
changes into CondMenu.
When CondMenu is ON, this
changes into CondMenu.
Rrturn to SWASH BASIC MAP. 1/2
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba CGY750 V 2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba CGY750 V 2.0 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info