29053
70
Zoom out
Zoom in
Previous page
1/78
Next page
Sailplane Section
Mode Setting
Press the A key to activate mixing, then press the
ACT or
INH
key ( F or G ) to activate or inhibit the
trim mix 1 (or 2) function. Now you will input the
desired presets for the elevator, ailerons, and speed flaps.
Setting the Elevator Preset Amount
Press the
B
key and set the rate with the numeric
keys E to M. The initial preset value is set to 0%, but
may vary from -100 to +100%.
Entering the Aileron 1 Servo Preset Amount
Press the C key and set the rate with the numeric
keys
E to M .
The setting range may vary from -100 to
+100% and the initial value is 0%.
Aileron 2 Servo Preset Inputting
Press
the D key and
set
the rate
with
the numeric
keys E to M , as before. If your linkages and horns are
identical, this setting should be the same as for Aileron 1.
Speed Flap 1 Preset
To get to the Flap preset inputting menu, press the
NXT Q
key. Then press the C key and set the rate
with the numeric keys E to M. As with the ailerons, the
initial value is set to 0%, but may vary from -100 to
+100%.
Speed Flap 2 Preset
Press
the D key and
set
the
rate
with
the numeric
keys E to M, as before. If your linkages and horns are
identicalM, this setting should be the same as for Speed
Flap 1.
Delay Rate Setting
Press the
R
key and set the rate with the numeric
keys F to
M.
The initial delay is set to 0%, but may
vary from 0 to 100%. A 100% delay takes about five
seconds to complete changing.
ON/OFF Switch Setting
An ON/OFF switch is not defined initially. To define
one, display the switch setting screen by pressing the
SWT P
key. Use the keys to choose the switch and ON
direction you want. For a description of the switch setting
method, see page 37.
We recommend using the three-position switch for
Trim Mix activation. The lower position is usually defined
to be the launch mode (use TM1), middle position is
normal, and the upper position is used for the speed
settings (use TM2).
If you use the three position switch, you will want to
activate Trim mix on the middle position also. This will
give the delay in switching both to and From the trim
mix.
Trim Volume Control and Direction Setting
You may adjust all the presets as a group, but a
volume control is not defined initially. Call the volume
setting screen by pressing the
VOL O
key. The volume
setting method is described on page 37. The volume con-
trol adds or subtracts ± 25% from all the preset positions.
Sailplane Section, Page 146
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info