29053

Futaba 9ZHP_part2 Manual

72
Zoom out
Zoom in
Previous page
1/78
Next page
Sailplane Section
ELEVATOR-FLAP Mix
(E-F)—2-S
This mixing is used to droop the flaps whenever
an up elevator command is given (and may be
set up for down elevator as well, helpful during
'outside' maneuvers). It helps aerobatic aircraft to
make tight, square corners in maneuvers.
Elevator-to-flap mixing can be set up to
be
turned on and off during flight by a switch (if no
switch is activated, this mixing remains on all the
time).
You
can
also
set
the
flap
trim
rate
in
this
function. If the flaperon function is activated, the
elevators are mixed with the ailerons, otherwise,
the mixing is with the flaps only.
Setting Up Elevator-to-Flap Mixing
Activation of command
In the Condition Menu, press the
E->F
key to get the
ELE TO FLP menu shown below. Use the A key
to activate mode setting, then press the ACT or INH
keys (F and G)
to
activate
or
inhibit
Elevator-to-Flap.
Mixing State
Mode setting
Mixing
rate
setting
ON/OFF switch
setting
Trimming
volume
setting
Return to Condition
screen
Set Value. Including Volume Adjustment
Mode Selection
Setting the Mixing Ratio - Down and Up Side
You now set the amount of mixing for down elevator
command. Press the C key to activate mixing ratio for
the Down direction and set the value with the numeric
keys E to M . The number keys
0
through
100
input
the value directly. The + and - keys increase or de-
crease the value by 1. The +/- key may be used to
reverse the throw direction. Your setting may vary from
-100 to +100%, the initial value is set to +50%.
Now set the amount of mixing for the up elevator
command. Press the D key to activate mixing ratio for
the Up direction and set the throw with the numeric keys
as before.
On/Off Switch Setting
On initial setting, the activation switch for Elevator-to-
Flap mixing is set as SW C on at the upper position. If
you would like to change the switch or turn mixing on all
the time, call the Switch Setting screen by pressing the
SWT P
key. Then use the keys to choose the desired
switch location and on direction. For more information
on the switch setting method, see page 37).
Mixing Rate Trim Volume Selection and Operating
Direction
A mixing rate volume control is not defined initially.
To define one, display the volume setting screen by
pressing the
VOL O
key. For a description of the
volume setting method, see page 37. The volume control
adjusts ±25% of the set mixing rate.
Use the
END ( N)
key to leave this menu.
Sailplane Section, Page 148
… 72 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info