29053

Futaba 9ZHP_part2 Manual

48
Zoom out
Zoom in
Previous page
1/78
Next page
Sailplane Section
16
Instruction 2-S 4-S 5-S
After a few flights to trim the model, you may set you may go through the Condition menu items to
different flight modes. You may trim for launch flap/ get the desired settings in the new mode. Read the
aileron droop, speed camber reflex, or other desired condition name after the model name to be sure you
flight modes. You can have different subtrims, rudder are changing the condition you want.
coupling, differential, aileron/speed flap mixing. In Now, you may go through the Condition menu items
fact you may change EVERY parameter between (i.e. ADF, A->R, etc.) to get the desired settings in
flight modes, the new mode. Read the condition name after the
Use the Condition Select CSL button in the Model model name to be sure you are changing the condition
Menu. This function allocates the necessary number you want.
of flight conditions to the model memory. Note the As an example, for NORML we use approximately
condition number next to the D (default) in the 50% ASF mixing, 50% differential, and 10% A->R
display. This is the set of conditions that will be coupling. In the speed mode, we use 100% ASF for
copied into a new condition and modified. Also note better roll rate, 0% differential, and turn A->R down
the number after the next display. You will copy to to zero because adverse yaw is very small at high
this condition, speeds. Subtrims and Trim Mixes 1 &2 may be used
Now use the Copy Condition CPC from the System to offset controls for different conditions, like flap
menu to copy the contents of the default condition droop for launch.
into another. Choose the default flight condition You can modify all of the settings and adjust each as
number, press the SET button, then choose the you like. You can add a time delay on many of the
second condition number in the lower box "TO menus: look for a DELAY setting. You can also have
CONDITION." Give the command to copy. the mixing ratio vary with the motion of another
The switch that calls the flight conditions should be slider or knob: look for the VOL key on the El
selected. Return to the Condition Select CSL button in some menus.
function, press the desired flight condition number, (Note: In the 4-servo model, if you don't mind having
and use the SWT button to choose the desired the same differential, mixing, etc. settings for all
switch location, modes, you can easily set Trim Mix 1 & Trim Mix 2
Once you have selected a condition, use the CNA TM1 , TM2 to droop flaps and ailerons, and trim
(Condition Name) button to label the new condition elevator for both launching and speed. Then you do
(you may have to flip the chosen switch to the not have to use any other flight condition settings.)
correct position to get the desired condition). Now,
After test flying, change compensation for glide path commands reacting & changing trim:
17
18
19
20
Instruction
Set elevator presets for launch and speed, or other flight conditions as desired. Make small changes.
Reduce rudder coupling A->R if fuselage points inward to center of turns, and increase if the fuse points
outwards during turns. Turn it off for speed.
Glidepath
trim
correction (Caution:
make only small changes
in elevator mixing)
Airbrake or spoiler trim
correction
2-S
For flap actuation trim
change: Set
Flap->EIev F->E
Use Airbrake->Elevator ABE mixing to correct trim change due to airbrake/
spoiler. Make small changes as trim is very sensitive to this.
4-S
For Butterfly trim
change: Set Butterfly-
Elev BYE
5-S
Set Butterfly-Elev
BYE . Brake
Flap->Elev
BKF
Sailplane Section, Page 124
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info