29053

Futaba 9ZHP_part2 Manual

24
Zoom out
Zoom in
Previous page
1/78
Next page
Helicopter Section
3. Idle-up 2 . . . .ON at SW (E) . .. . .Used for rolling
Forward position aerobatics.
4. Throttle . . . .ON at SW (G) .... .Activate for
Hold Forward position autorotation.
In
the
case
above,
the
flight
condition
priority
is
4>3>2>D,
with
4
having the highest
priority.
This
means that if the Idle-Up 1 switch is on, and Throttle
hold is turned on, the system will use the Throttle
hold settings.
To set the condition data for each flight condi-
tion, be sure that you call the appropriate condition
by turning on the correct switch (as given above).
Read the condition name after the model name to be
sure you are changing the condition you want.
8 Normal Flight Programs
Select the Normal flight settings by turning off
all the flight condition switches.
9 Throttle Curve Setting
Call the Throttle Curve
THA
function from the
Model Menu. Check to see that it is activated ACT .
Next, move to the condition menu and press
TCV
to get the setting menu. Set the throttle curve
to the values shown in the table below:
The throttle responds slowly at first and then the
response rate increases at the top end.
10
Pitch Curve Setting
Call the pitch curve PIT function from the
model menu. Verify that the PIT curve function is
activated (
ACT ).
The following settings assume a semi-symmetrical
rotor blade with no twist. For the pitch curve, the
initial LOW rate is 100% and the HIGH rate is 100%.
Set the maximum pitch angle in advance. The pitch
angle is -4° to +12°.
When setting the pitch angle, set the hovering
pitch lever and the HIGH side pitch lever to the
center positions. These levers may be activated in
flight to make adjustments. Next, input the data so
that the normal pitch used in hovering becomes
-2.5° to+10° by LOW/HIGH side rate setting.
Although unimportant in calm conditions, the
pitch angle should be set to that the High side pitch
rate is large. This provides high collective sensitivity
to help cope with windy conditions.
Pitch Curve Setting.
Move to the Condition menu, and select the pitch
curve PCV key. Set the pitch curve to the follow-
ing values:
Point
Setting (%)
1
9
2
18
3
27
4
35
5
43
6
52
7
59
8
67
9
73
10
11
78 82
11
86
13
88
The rise at the low end is fast, and then the rise
rate
is reduced at the high end. We recommend
setting the hovering pitch to +4.5°.
11 Flight Condition Copying
Use the Condition Select
CSL
button in the
Model Menu. This function displays the flight condi-
tions associated with the model in active memory.
Note the condition number next to the D (default)
in the display. This is the set of conditions associated
with the trimmed model. Also note the three num-
bers following: these are the conditions associated
with Idle-up 1&2 and Throttle Hold, that will be
copied into and modified.
Use the Copy Condition CPC from the System
menu. This function may be used to copy the con-
tents of one condition into another. Choose the
default flight condition number (next to the D),
press the
SET
button, then choose the Idle-up 1
condition number in the lower box "TO CONDI-
TION." Give the command to copy. Repeat for
Idle-up 2 and Throttle-hold conditions.
Normal->-ldle-up 1
Normal->ldle-up 1
Normal->Throttle Hold
Helicopter Section, Page 100
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info