29053
13
Zoom out
Zoom in
Previous page
1/78
Next page
Airplane Section
FLAPERONS
(FPN)
This function allows you to program the
ailerons to work in the same direction, giving a
flap response as well as aileron control (see figure).
For good square maneuvers, and landing, both
ailerons can be raised and lowered simultaneously.
While this function is on, regular aileron operation
is always present.
The Flaperon function requires two separate
channels: Receiver CH1 (aileron 1/flap 2) and CH6
(aileron 2/flap 1) are the operating channels. The
Aileron 1 and Aileron 2 left and right deflection
angles can be adjusted independently, making it
easy to apply differential to the ailerons. With
differential, the up side travel is set to around 5%
larger than the down travel.
You may also adjust the
Flap
1 and Flap 2
throws independently, and you can set the flap
trim
rate
as
large
or
small
as
you
like.
Also,
the
flap trim offset can be adjusted, allowing you to
freely change the flap neutral angle.
Aileron operation
Flap operation
Setting Up Flaperons
Activation of command
In the Condition Menu, press the
FLP
key to get the
FLAPERON menu as shown below. Use the A key
to activate mode setting, then press the
ACT
or
INH
keys
(F and G) to
activate or
inhibit
the
function.
Mode setting
Aileron 1 Left
Side Travel
Aileron 2 Left
Side Travel
Flap 2 Travel
Setting
To Next Screen
Aileron 1 Right
Side Travel
Aileron 2 Right
Side Travel
Flap 1 Travel
Setting
Return
to
condition menu
Mode Selection
Setting the Aileron 1 Travel
You now set the left-side travel for Aileron 1. Press the
B
key to activate left travel setting for Aileron 1 and set
the travel with the numeric keys E to M . The number
keys 0
through 100 input the
value
directly. The +
and - keys increase or decrease the value by 1. The
+/- key may be used to reverse the throw direction.
If you are not sure what you are changing, hold the
stick to one side and press different keys — if there is no
effect, move the aileron stick to the other side and con-
tinue. Your setting may vary from —120 to +120%, with
an initial value of +100%.
Now set the right-side travel for Aileron 1. Press the
Q
key to activate Aileron 1 right travel setting and set
the travel with the numeric keys as before.
Setting the Aileron 2 Travels
This procedure
is
repeated for Aileron 2.
Press
theC
key to activate left travel setting for Aileron 2 and set the
travel with the numeric keys Eto M as before.
Now set the right-side travel for Aileron 2. Press the
P key to activate Aileron 2 right travel setting and set
the travel as before.
Setting the Flap Travels — 1 and 2
You now
set
the
travel
for
Flap
2.
Press
the D key
to
activate travel setting for Flap 2 and set the travel with
the numeric keys E to M . Your setting may vary from
-100 to +100%, with an initial value of +100%.
Now set the travel for Flap 1. Press the
O
key to
activate Flap 1 travel setting and set its travel with the
numeric keys. Its initial value is -100%.
Airplane Section, Page 89
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info