29053
12
Zoom out
Zoom in
Previous page
1/78
Next page
Airplane Section
AlLEVATORS/COMBINED AlLERONS & ELEVATORS (ALV)
This
function
allows
you
to
hook
up
the
eleva-
tor surface on each side of the airplane independ-
ently,
so
that
they
operate
together
(elevator
mode) and differentially (aileron mode). This
function,
sometimes called
"ailevators"
(ALV)
will
give aileron control even at low speeds, because
the
propeller
wash
is
always passing over
the
tail
surfaces and may be used for rolling commands.
This function requires two elevator servos con-
nected to receiver output channels 2 and 5. In this
manual (see diagram), the rear control surfaces are
referred to as Aileron 3 and Aileron 4. With this
function, all control deflections left and right
ailerons,
and
elevator
on
both
sides
can
be
adjusted. You may even add differential to the rear
ailerons.
Setting Up Differential
Elevators
Activation of command
In the Condition Menu, press the ALV key to get the
AILVATOR menu shown below. Use the A key to
activate mode setting, then press the ACT or INH
keys (F and
G)
to activate or inhibit the function.
Mode setting
Aileron 3 Left.
Side Rate
Aileron 4 Left
Side Rate
Elevator 1 Rate
Setting
Aileron 3 Right
Side Rate
Aileron 4 Right
Side Rate
Elevator 2 Rate
Setting
Return to
condition menu
Mode Activation
Setting the Aileron 3 Rates
You now set the left-side travel for Aileron 3. Press the
B key to activate left rate setting for Aileron 3 and set
the rate with the numeric keys E to M . The number
keys 0
through 100
input
the
value
directly. The +
and - keys increase or decrease the value by 1. The
+/-
key may be used to reverse the throw direction.
Your setting may vary from -100 to +100%,the initial
value is-50%.
Now set the right-side rate for Aileron 3. Press the Q
key to activate Aileron 3 right rate setting and set the rate
with the numeric keys as before.
Setting the Aileron 4 Rates
This procedure
is
repeated
for
Aileron
4.
Press
the C
key to activate left rate setting for Aileron 4 and set the
rate with the numeric keys E to M as before. The max
values and initial setting are the same as for Aileron 3.
Now set the right-side rate for Aileron 4. Press the 13
key to activate Aileron 4 right rate setting and set the rate
as before.
Setting the Elevator Rates - 1 and 2
You now set the rate for Elevator 1. press the D key
to activate rate setting for Elevator 1 and set the rate with
the numeric keys E to M . The initial rate is 100%, but
you may vary your setting between -100 and +100%.
Now set the rate for Elevator 2. Press the
O
key to
activate Elevator 2 rate setting and set its rate with the
numeric keys. Settings have the same range as Elevator 1.
Checking Your Work
After you have set up the Ailevator rates, be sure that
they move the correct directions. For up elevator com-
mand, both elevators should move upward. For right
aileron command, the trailing edge of the right-hand
surface should move up. and the trailing edge of the left-
hand surface should move down. If they do not, use the
+/- to reverse the direction as needed. Adjust the
travels on either side to get the differential effect, if you
wish.
Exiting
Use the
END ( N
) key to leave this menu.
Airplane Section, Page 88
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info