29053

Futaba 9ZHP_part2 Manual

10
Zoom out
Zoom in
Previous page
1/78
Next page
Airplane Section
FLAP-ELEVATOR
Mix (F-E)
This
function
is
used
to
compensate
for
trim
changes when flaps are deployed for show flight or
landing by mixing in a small movement of elevator.
The elevator should be adjusted to move only a
small deflection amount: too much elevator can
make the model difficult to control.
The amount of correction can be adjusted sepa-
rately for both positive and negative flap inputs,
and the neutral mixing position can be offset from
the flap neutral position. Flap-to-elevator mixing
can be turned on and off during flight by setting a
switch, but if an ON/OFF switch is not set, it
remains on all the time. The amount of mixing can
be changed by setting a volume control.
Setting Up Flap-to-Elevator Mixing
Activation of command
In the Condition Menu, press the
F-E
key to get the
FLP TO ELE menu shown below.
Mode setting
Offset amount setting
Mixing
rate
setting
U
ON/OFF switch
setting
Trimming volume
setting
Return to Condition
screen
Down side
Up side
Mode Selection Rate including volume adjustment
Use the A ( ) key to activate mode setting, then press
the ACT or INH
keys
(F and G)
to
activate
or
inhibit flap-to-elevator coupling.
Offset Position Setting
Use the B key to activate offset setting mode.
Then set the flap control to the offset position, and
press the SET key F to store the desired position in
memory.
Setting the Mixing Ratio — Down and Up Side
You now set the amount of mixing for down flap com-
mand. Press the C key to activate mixing ratio for the
down direction and set the value with the numeric keys
E to M .
The number keys 0 through
100
input the
value directly. The + and - keys increase or decrease
the value by 1. The +/- key may be used to reverse the
throw direction. Your setting may vary from —100 to
+100%, the initial value is set to +50%.
Now set the amount of mixing for the up elevator
command. Press the D key to activate mixing ratio for
the Up direction and set the throw with the numeric keys
as before.
On/Off Switch Setting
Initially an activation switch for is not set, meaning
that once activated, this function is on all the time. If you
would like to set a switch to turn it on and off, call the
Switch Setting screen by pressing the
SWT P
key.
Then use the keys to choose the desired switch location
and on direction. For more information on the switch
setting method, see page 37.
Trim volume setting
You may set up the Flap-to-Elevator mixing so that its
effect may be changed in flight by moving a trim control.
The trim control allows you to adjust the volume within
±25% of the set mixing rate, which can be handy for
getting the best value while flying the model. This option
is not activated at initial setup.
Call the volume setting screen by pressing the VOL
O key, and select the desired control using the screen
menus (for a description of the volume setting method,
see page 37).
Use the
END
N key to leave this menu.
Airplane Section, Page 86
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info