Manual Futaba 9ZHP_part2 (page 9 of 78) (English)

29053

Zoom out

Zoom in

1/78

Airplane Section

ELEVATOR- FLAP (E-F)

This mixing is used to droop the flaps whenever

an up elevator command is given (and may be set

up for down elevator as well, helpful during

'outside' maneuvers). It helps to eliminate 'buck-

ing,' and makes tight, square corners in maneuvers

for acrobatic aircraft.

Elevator-to-flap mixing can be set up to be

turned on and off during flight by a switch (if no

switch is activated, this mixing remains on all the

time).

You

can

also

set

the

flap

trim

rate

this

function. If the flaperon function is activated, the

elevators are mixed with the ailerons, otherwise,

the

mixing

with

the

flaps

only.

Setting Up Elevator-to-Flap Mixing

Activation of command

In the Condition Menu, press the

E->F

key to get the

ELE TO FPR menu shown below. Use the A key

activate

mode setting, then

press

the ACT or INH

keys ( F and G) to activate or inhibit Elevator-to-Flap.

ON/OFF switch

setting

Return to

Condition screen

Mode setting

Flap trim rate

Down side

Up side

Mixing

rate

setting

Mode Selection

Setting the Mixing Ratio — Down and Up Side

You now set the amount of mixing for down elevator

command. Press the C key to activate mixing ratio for

the Down direction and set the value with the numeric

keys E to

The number keys 0 through

100

input

the value directly. The + and - keys increase or de-

crease the value by 1. The +/- key may be used to

reverse the throw direction. Your setting may vary from

-100 to +100%, the initial value is set to +50%.

Now set the amount of mixing for the up elevator

command. Press the D key to activate mixing ratio for

the Up direction and set the throw with the numeric keys

as before.

Flap Trim Rate Setting

You may choose any value for the Flap Trim Rate.

Knob (A) is used to trim the position of the flap servo,

and the trim value controls the authority of the knob.

The authority may be set anywhere from 0% to 100%,

and the initial setting is 30%.

Call the flap trim setting screen by pressing the TRIM

RATE B key, and select the desired trim rate using the

screen menus. You may want a small number for this rate,

so that an accidental movement of the knob doesn't give a

large flap deflection.

On/Off Switch Setting

On initial setting, the activation switch for Elevator-to-

Flap mixing is set as SW (C) on at the upper position. If

you would like to change the switch or turn mixing on all

the time, call the Switch Setting screen by pressing the

SWT P

key. Then use the keys to choose the desired

switch location and on direction. For more information

on the switch setting method, see page 37).

Use the

END ( N )

key to leave this menu.

Airplane Section, Page 85

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba 9ZHP_part2 Manual

Product: