29053
15
Zoom out
Zoom in
Previous page
1/78
Next page
Airplane Section
AIRBRAKE
(ABK)
Airbrake presets are used to set up preset
deflections of the elevators, flaps, and (optionally)
spoilers for landing precision or for constant speed
during vertical flight maneuvers. Airbrake presets
can be turned on and off during flight by ON/OFF
switch, or you may define an AUTO mode where
mixing is turned on and off automatically by
throttle stick position.
The AUTO mode, if used, may be turned on
and off with a switch. However, a command on
the
air
brake
has
priority
and
is
followed
regardless
of the position of the AUTO mode ON/OFF
switch.
Suggested settings for the Airbrake function are
a flap deflection of +50%. The elevators will need
to be set to about -20 to 23%. Of course, the
elevators should be adjusted so that the model
maintains
level
flight
when
the
Airbrake
function
is operated.
Setting Up The Airbrake Presets
Activation of command
In the Condition Menu, press the
ABK
key to get the
AIR BRAKE menu as shown below.
Mode setting
Flap Preset
Position Setting
Elevator Preset
Position Setting
Flap Trim Rate
Setting
Spoiler Setting
Air brake ON/OFF
Switch Setting
Return
to
condition menu
Airbrake Mode Selection
Use the A key to activate mode setting, and
press the ACT F key to activate the function. Now
you must decide on Manual or Auto operation. Select the
manual mode by pressing the MAN ( G) key. Select the
auto mode by pressing the
AUT
H key.
Throttle Position Setting (Auto Mode Only)
For the Auto mode, you need to input the position at
which the function will take effect. Press the B key, then
move the throttle stick to the desired position, and press
the
SET
( F ) key to memorize the position.
Flap Preset Position Setting
To set the position that the flaps will move to, press
the C key and use the rate setting keys
E to M
. This
setting may vary from -100 to 100%, and is initially set
to
50%.
Elevator Preset Position Setting
To set the position that the elevators will move to,
press the D key and use the rate setting keys E to M .
This setting may vary from -100 to 100%, and is initially
set to -30% by the system.
Flap Trim Authority Setting
Flap Trim moves both ailerons upwards or downwards
together. To input the Flap Trim Authority, press the
NXT R
key. Then set the rate with the numeric keys
E to M. You may choose any value from 0% to 100%
for the Flap Trim Authority. The initial setting is 30%,
but a smaller number is recommended. If you input a
number here, it will override whatever value was input in
the Flaperon menu.
Airplane Section, Page 91
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info