29011
32
Zoom out
Zoom in
Previous page
1/78
Next page
System Section
DTN—DATA TRANSFER FUNCTION
This function may be used to exchange model
setup data between two PCM 1024Z transmitters.
Identical model setups are needed for trainer oper-
ation,
and
it
is
also useful
to
transfer data
to
a
friend's transmitter to speed the setup process for
a model with complicated mixing and flight
modes, to avoid doing the setup process from
scratch.
An optional Trainer/Data Transfer Cable is
necessary for this operation. The time needed
to
transfer data depends on the number of flight con-
ditions, and ranges from 1 to 18 seconds.
Data Transfer Mode Setup
First, connect the two PCM 1024Z transmitters
with the data transfer cord. To place the PCM
1024Z into the Data Transfer mode, press the
DTN key from the System Menu. Then, follow
the following instructions (if you want to start
over
the
beginning,
press
the
abort ABT key L.
Model Memory Menu
Transmit
Receive
Return to System
Menu
Source Transmitter
(with the desired model setup
stored in its memory)
1. Press the TRN ( K ) key.
2. Select the Source model (to be
copied) with the A to J ( 1to
10 ) keys.
6. Press the TNS ( K ) key to
have the Source transmitter send
the desired data.
7a A successful transfer displays the
message "TRANSMITTING . . .
COMPLETED". If an error is
generated, the display will read
"ERROR:DATA FAULT
PLEASE RETRY".
8. To continue data transfer, press
the CNT ( L ) key. To end, press
END (N)
.
Destination Transmitter
(to be loaded with the setups from
the Source transmitter)
3. Press the RCV ( L ) key.
4. Use the A to J keys ( 1 to 10 )
to select the memory in which the
source model is to be stored.
5. Press the RCV ( K ) key to
place the Destination transmitter
into the receive mode.
7b When the data transfer is
successful, the message
"RECEIVING . . . COMPLETED"
is displayed. If an error is
generated, the display will read
"ERROR:DATA FAULT PLEASE
RETRY".
8. To continue data transfer, press the
CNT ( L ) key. To end, press END
(N).
Trainer/Data Transfer Cord
Connector
System Section, Page 30
Target Transmitter
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part1 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info