29047

Futaba 9ZAP_part1 Manual

50
Zoom out
Zoom in
Previous page
1/78
Next page
Model Setting Section
CHD—CONDITION HOLD
This
function
may
be
used
to
limit
the maxi-
mum speed of the engine so that you may adjust
flight conditions when the engine is running. The
maximum throttle position is settable, and an
alarm indicates that the function is operating. The
function is especially useful for helicopters, be-
cause it will prevent the engine from racing dan-
gerously when adjusting the Idle-Up settings.
While this function is active, the throttle oper-
ates on the default condition throttle curve, and
mixing is applied as normal, except the throttle is
not allowed to move past the set point.
You must deactivate this function when you are
through making adjustments. The system will not
allow you to deactivate this function in either of
the following states:
1. When all the flight condition switches are off
2. When the throttle stick is lower than the set
point.
In
either
of
these
two
states,
you
will
receive
the
warning message "TO INHIBIT TURN OFF
SPECIAL CONDITION AND LOWER THROT-
TLE PAST MAX SET POINT", and will not be
allowed to turn off the Condition Hold function
until
the
states
are
turned off.
Condition Hold Setting Procedure
Activation of command In the Model Menu. press the
CHD key
to
get
the function modification menu.
Activate Mode
Selection Keys
Maximum
Throttle Travel
Return to Model
Menu
Activate/Inhibit Keys
Use the
A
key to activate mode setting, then press the
ACT
or INH
keys
( F
and G
)
to activate or
inhibit
the condition hold function.
Throttle Servo Maximum Throw Setting You now set
the amount of throttle servo throw. Press the
B
key to
activate throttle travel setting, place the throttle stick in
the desired position, and then use the SET
(F)
key to
enter the position into memory. Use the
END (N)
key
to leave this menu.
NOTE: You may also activate the condition hold func-
tion from the Condition menu by pressing the
M
key, or from the Normal Display by pressing
the G key.
Model Setting Section, Page 48
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZAP_part1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZAP_part1 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info