29047

Futaba 9ZAP_part1 Manual

49
Zoom out
Zoom in
Previous page
1/78
Next page
Model Setting Section
CUT—ENGINE CUT
This function may be used to define a switch
setting
that
may
be used
to
cut
the
engine.
It
will
only work when the throttle stick is at the low
side; the throttle position may be set.
When this function is actuated with the throttle
stick below the set threshold, the throttle servo is
commanded to an offset position (there is no
effect above the threshold position). When activat-
ed, the Alarm light flashes to remind you the com-
mand is on.
Airplane
Offset Direction
Helicopter
0 Position
-100%
Slow Side
+100%
Engine Cut Setting Procedure
Activation of command In the Model Menu, press the
CUT key to get the Engine Cut menu.
Function State Display (ON/OFF)
Mode Setting
Throttle Position
Setting
Offset Throw Setting
ON/OFF
Switch Setting
Return to
Model Menu
Mode Selection
Use the
A
key to activate mode setting, then press
the ACT or
INH
keys (F and G) to activate or
inhibit the engine cut command.
Threshold Setting Now you will set the throttle posi-
tion that the engine cut command will operate under-
neath: press the
B
key to activate position setting, place
the throttle stick in the desired position, and then use the
SET (F) key to enter the position into memory. If
the throttle stick is above this position, CUT will not
occu r.
Throttle Servo Offset Setting You now set the amount
and
direction
of throttle
servo
throw.
Press
the C right-
arrow key and set the rate with the numeric keys. The
number keys (0) through (
100
) input the value
directly. The ( + ) and ( - ) keys increase or decrease
the value by 1. The +/- key may be used to reverse the
offset direction.
Setting the Engine Cut Command Switch Call the
Switch Setting screen by pressing the
SWT
(
P
) key.
Set the desired switch using the instructions on page 37.
When complete, press the
PRE
button (N) to return
to the previous screen. Use the
END ( N )
key to leave
this menu.
Model Setting Section, Page 47
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZAP_part1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZAP_part1 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info