Manual Futaba 9CPsuper (page 75 of 109) (English)

29049

Zoom out

Zoom in

1/109

OFFSETS (GLID2FL-C only): additional flight conditions available specifically for sailplanes.

These additional flight conditions contain different offset trims to make the saiplane perform certain maneuvers more

easily. Aileron differential functions may be set to provide separate rates per condition selected.

The 9C super provides 3 offset trims to allow the modeler 3 additional setups along with the normal flight condition.

(OFFSET-1, OFFSET-2, and OFFSET-3) These offset trims have same setting abilities basically except the switch and dial

assignment. For an example of trim settings, please see the following:

OFFSET-1: is used to offset the aileron, elevator, and flap servos to the position that provides maximum lift during launch

(Start Offset). Normally the ailerons and flaps are drooped about 20-30%, withthe flaps drooped slightly more to prevent

tip-stalling on tow. The elevator can also be offset in order to trim out any pitch changes caused by the flap and aileron

presets.

OFFSET-2: is used to offset the aileron, elevator, and flap servos for minimum drag in cruiseand high-speed flight

(Speed Offset). Normally the ailerons and flaps are raised about 3-5%.

Adjustability:

•Separate adjustments for each aileron, elevator, and flap servo. (OFFSET-1, -2, and -3)

•S

WITCHG(9CA) or E(9CH) is programmed for normal (NORM), OFFSET-1, and OFFSET-2

trims. S

WITCHH(9CA) or F(9CH) is programmed for OFFSET-3 trim. These

switch/position assignment is adjustable. (SW/MODE)

OFS1/2-SW: 3-position type switch only, OFS3-SW: 2-position type switch only

•

TRIM item (Digital trim operation mode): NORM: normal trim operation mode, MIX: offset rate trim

operation mode while mixing is on.

•Optional assignable knob (CAMBER) to allow trimming in flight of the aileron and flap

action of each flight condition.

*During OFFSET operation, the aileron and elevator travels are displayed on each trim

display in the Startup screen.

GOAL of EXAMPLE: STEPS: INPUTS:

Activate the function.

Close the function.

to 2nd page.

to OFF.

to AIL1.

Set up a OFFSET-1 to gain maximum

possible lift on launch.

Each Aileron: 50%.

Each Flap: 100%.

Elevator: -5% to compensate.

Open OFFSET-1 function.

for 1 second.

(If BASIC menu, again.)

to OFFSET-1.

Set the rates. (Ex: AIL1 and 2, 50%,

FLP1 and 2, 100%, ELEV -5%.)

to +50%. to AIL2.

to -5%. to ELEV.

Repeat for, FLP1 and 2, AIL2.

WITCH(9CAS=G, 9CHS=E.)

Note: switch is assignable. (SW/MODE)

NOB(null)

Note: knob is assignable. (CAMBER)

View additional model setups on the internet: www.futaba-rc.com\faq\faq-9c.html.

Where next?

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba 9CPsuper Manual

Product: