29049

Futaba 9CPsuper Manual

73
Zoom out
Zoom in
Previous page
1/109
Next page
Launch (Start) Offset (START OFS) (GLID1FLAP/GLID2FLAP only): The Start function is used to offset the aileron,
elevator, and flap servos to the position that provides maximum lift during launch. Normally the ailerons and flaps
are drooped about 20-30, with the flaps drooped slightly more to prevent tip-stalling on tow. The elevator can also
be offset in order to trim out any pitch changes caused by the flap and aileron presets.
*During Launch Offset operation, the aileron and elevator travels are displayed on each trim display in the Startup
screen.
Adjustability:
Switch: This function is activated by flipping SWITCH G (9CA) to the back position.
Mix switch is selectable (3-position type switch only) in
the OFSET-SW item. (SW/MODE)
Separate adjustments for each aileron and flap servo (two flap settings for GLID2FLAP) and for elevator.
RANGE for each adjustment is -100 to +100.
Optional assignable dial (VR) to adjust all 4 wing servos in unison, 1% at a time, across all 4 servos in flight.
GOAL of EXAMPLE: STEPS: INPUTS:
73
Set up a START OFS to gain maximum
possible lift on launch.
Each Aileron: 50%.
Each Flap: 100%.
Elevator: -5% to compensate.
Where next?
Open START OFS function.
Activate the function.
Set the rates. (Ex: AIL1 and 2, 50%,
FLAP1 and 2, 100%, ELEV-5%.)
Optional: set a knob to adjust travel
of all 4 wing servos in flight.
Close the function.
for 1 second.
(If BASIC menu , again.)
to 2nd page. to START OFS.
Flip switch G toward you.
to OFF.
to AIL1.
to +50%. to AIL2.
to +50%. to ELEV.
Repeat for ELEV, FLP1 and 2, AIL2.
to desired knob.
SPEED OFS mixing. See p. 74.
BUTTERFLY. See p. 56.
Create a programmable mix to meet your model's setups: see p. 60.
View additional model setups on the internet: www.futaba-rc.com\faq\faq-9c.html.
•
•
•
•
•
•
Digital trim operation mode: Operation mode
is selectable.
NORM: Normal digital trim operation
MIX: START OFS mixing rate trim operation while mixing is on.
… 73 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info