29049

Futaba 9CPsuper Manual

76
Zoom out
Zoom in
Previous page
1/109
Next page
76
BUTTERFLY (crow) mixing (GLID2FL-C):
BUTTERFLY (often called "crow" - see GLID, p. 71 for details) simultaneously moves the flap, twin ailerons and elevator,
and is usually used to make steep descents or to limit increases in airspeed in dives.
Adjustability:
• Activation: Proportional by moving the T
HROTTLESTICK.
• Switch: Mix S
WITCH is selectable. (SW/MODE function - B.FLY-SW item)
A to H: S
WITCH A to H NULL: always on.
• Digital trim operation mode: Operation mode
is selectable.
NORM: Normal digital trim operation
MIX: BUTTERFLY mixing rate trim operation while mixing is on.
• Inversely proportional to T
HROTTLESTICK: provides a proportional increase in amount of airbrake action as
T
HROTTLESTICK is lowered (when SWITCH A (assignable) is in down position). Includes selectable stick position where
airbrake begins. If you would like to have the airbrake be directly proportional to throttle stick, you will need to reverse
the THR-REV function. Note that this changes the throttle stick direction for all models. See page 31 for instructions.
• Elevator settings: (adjustable in the B.FLY-ELE)
B.FLY-ELE works linking with BUTTERFLY function. Elevator rate is adjustable in a
3 point curve.
Point 1: PRESET point. (Fixed)
Point 2: P-mid point. Position and rate are adjustable.
Point 3: P-end point. Position and rate are adjustable.
• Delayed reaction: You can suppress sudden changes in your model's attitude when BUTTERFLY is activated by setting
the delay (DELAY) item, to slow down the elevator response, allowing the flaps/ailerons/elevator to all reach their desired
end point together. A setting of 100% slows the servo to take approximately one second to travel the prescribed distance.
• Channels controlled: Elevator, twin ailerons and flap may be set independently in BUTTERFLY, including set to 0 to have
no effect.
• Twin aileron servos: If AIL-DIFF function is inhibited, then AIL1and AIL2 settings will have no effect.
• If AIL-DIFF is active, then CH1 and CH7 may be independently adjusted.
• Normally both ailerons are raised equally in BUTTERFLY, and the elevator motion is set to maintain trim when the
ailerons rise. Different amounts may be set for each aileron to correct for torque reactions and other unique
characteristics of the model.
Be sure you understand what dropping ailerons will do when in BUTTERFLY. Along with creating an enormous
amount of drag (desireble for spot landings), this also creates "wash-in", a higher angle of attack where the ailerons
are, and encourages tip stalling. If you are using this for aerobatic performance and not "sudden stops", consider
raising the ailerons and dropping the flaps instead as shown in the diagram above.
… 76 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info