28983
7
Zoom out
Zoom in
Previous page
1/24
Next page
Receiver
Charging
Jack
(Black)
Switch
Harness
To Battery
(Red)
7
RECEIVER AND SERVO CONNECTIONS
RECEIVER AND SERVO CONNECTIONS
Connect the servos to the receiver to perform the functions indicated:
Connect the servos to the receiver to perform the functions indicated:
Receiver
Receiver
output
output
channel
channel
Function
Function
1
2
3
4
5
6
7
B/8
B/8
Aileron -or
or
-right flaperon -or
or
-right elevon (for tailless models)
Elevator -or
or
-left ruddervator (for V-tail models) -or
or
-left elevon (for tailless models)
Throttle
Rudder -or-right ruddervator (for V-tail models)
Retractable landing gear
Flap -or-left flaperon
Not used
Receiver on/off switch (the plug colored red goes int o the receiver)
The diagram shown is for aircraft models only. Additional servos may have to be purchased separately.
Flap (or 2nd
Flaperon) Servo
(CH6)
Gear Servo
(CH5)
Rudder Servo
(CH4)
Throttle Servo
(CH3)
Elevator Servo
(CH2)
Aileron Servo
(CH1)
CHARGING THE Ni-Cd BATTERIES
CHARGING THE Ni-Cd BATTERIES
The transmitter and receiver batteries included with your 6EXAP system are rechargeable, Ni-Cd (nickel-cadmium, pronounced
ni-kad) batteries. Ni-Cd batteries require special care and charging. Read the charging instructionscarefully.
Read the charging instructionscarefully.
NOTE:
NOTE:
The batteries are supplied partially charged, but will require a full, overnight charge before the model may be flown.
1. Connect the transmitter charging cord
transmitter charging cord
coming from the A/C wall charger to the charge jack in the right side of the
transmitter case. The receiver charging cord
receiver charging cord
may be connected to the batteries two different ways: The charge cord
may be connected directly to the battery pack, or to the vacant charge connector (black) coming from the on/off switch in
the model. Charging
“through the switch” is preferred as there will be no need to disconnect the battery.
2. Plug the A/C wall charger into a wall outlet. Note:
Note:
If the wall outlet can be turned off by a switch in the room, be certain
the switch remains on after leaving the room. Otherwise, the batteries will not be charged!
3. The LEDs (light-emitting diodes) should light red, indicating that current is flowing and the batteries are being charged.
Discharged batteries will take about 15 hours to fully charge. If using an aftermarket fast charger, be certain to follow
be certain to follow
the manufacturer
the manufacturer
s instructions provided with the charger
s instructions provided with the charger
so you do not overcharge the batteries. NEVER
NEVER
charge
the batteries at a rate higher than 1,000mAh. The batteries should also be discharged periodically to prevent a condition
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6EXAP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6EXAP in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info