28983
5
Zoom out
Zoom in
Previous page
1/24
Next page
5
5
Charging jack -
Charging jack -
Port for charging the transmitter batteries with the included battery charger.
On-off switch
On-off switch
DATA INPUT lever -
DATA INPUT lever -
Used to change the values of the various functions displayed on the LCD screen.
Liquid-crystal display screen
Liquid-crystal display screen
(LCD) - Displays programming modes and values entered.
MODE key -
MODE key -
Used to scroll through and display the ten or eleven(PCM) different functions.
SELECT key -
SELECT key -
Used to display the values for the current function.
Throttle-cut button -
Throttle-cut button -
To use the throttle-cut function, lower the throttle stick all the way, then Push the throttle-cut button to
fully close the carburetor and shut of the engine.
Throttle/rudder control stick -
Throttle/rudder control stick -
Operates the servos connected to channel 3 (throttle) and channel 4 (rudder) in the receiver.
Trainer switch -
Trainer switch -
Operates the trainer functions. To operate as a trainer switch the transmitter must be connected to another
transmitter via. a trainer cord (available separately).
Retractable landing gear switch/Channel 5 -
Retractable landing gear switch/Channel 5 -
Switch operates the servo connected to channel 5 in the receiver if your
model has retractable landing gear this is the control used to extend and retract the gear.
Antenna -
Antenna -
Radiates signals to the receiver. Never fly a model without fully extending the antenna or you may create
interference to other modelers and decrease operational signal range of the transmitter. The antenna may be removed and
replaced with another in case it is inadvertently broken.
RADIO INSTALLATION
RADIO INSTALLATION
Follow these guidelines to properly mount the servos, receiver and battery.
Make certain the alignment tab
alignment tab
on the battery, switch and servo connectors is oriented correctly and keys into the
corresponding notch in the receiver or connectors before plugging them in. When unplugging connectors, never pull on the
wires. Always pull on the plastic connector instead.
If any servo wires are not long enough to reach the receiver, servo extension wires (available separately) may be used.
Always mount the servos with the supplied rubber grommets
rubber grommets
. Do not over tighten the
screws. No part of the servo casing should contact the mounting rails, servo tray or any
other part of the airplane structure. Otherwise, vibration will be transmitted to the servo
causing premature wear and/or servo failure.
Note the small numbers (1, 2, 3, 4) molded into each arm on the Futaba 4-arm servo arms.
The numbers indicate how many degrees each arm is
“off” from 90 degrees to correct for
minute manufacturing deviations from servo to servo.
To center the servos, connect them to the receiver and turn on
the transmitter and receiver. Center the trims on the
transmitter, then find the arm that will be perpendicular to the
pushrod when placed on the servo.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6EXAP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6EXAP in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info